ASRock A55 Pro manual Consumer Infrared Module Header

Page 30

Consumer Infrared Module Header

This header can be used to

(4-pin CIR1)

connect the remote

(see p.11 No. 23)

controller receiver.

Front Panel Audio Header

 

 

GND

(9-pin HD_AUDIO1)

 

 

 

 

PRESENCE#

 

 

 

 

 

 

MIC_RET

 

 

 

 

 

 

 

 

 

 

 

OUT_RET

(see p.11 No. 27)

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT2_L

 

 

 

 

 

 

 

 

J_SENSE

 

 

 

 

 

 

 

OUT2_R

 

 

 

 

 

MIC2_R

 

 

 

MIC2_L

This is an interface for the front panel audio cable that allows convenient connection and control of audio devices.

1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2.If you use AC’97 audio panel, please install it to the front panel audio header as below:

A.Connect Mic_IN (MIC) to MIC2_L.

B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C.Connect Ground (GND) to Ground (GND).

D.MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.

E.To activate the front mic.

For Windows® XP / XP 64-bit OS:

Select “Mixer”. Select “Recorder”. Then click “FrontMic”. For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:

Go to the "FrontMic" Tab in the Realtek Control panel. Adjust “Recording Volume”.

System Panel Header

This header accommodates

(9-pin PANEL1)

several system front panel

(see p.11 No. 15)

functions.

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may con- figure the way to turn off your system using the power switch.

30

Image 30
Contents A55 Pro Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Rear Panel I/O ConnectorBios Feature Support CDPage ASRock Instant Boot Unique FeaturesASRock Extreme Tuning Utility Axtu ASRock Instant FlashASRock XFast LAN ASRock APP ChargerASRock XFast USB ASRock XFast RAMMotherboard Layout ATXPWR1I/O Panel LAN Port LED IndicationsInstallation Pre-installation PrecautionsCPU Installation Installation of CPU Fan and HeatsinkInstallation of Memory Modules Dimm Installing a DimmInstalling an expansion card Expansion Slots PCI and PCI Express SlotsPcie Slots Graphics Card Setup CrossFireXTM and Quad CrossFireXTM Operation GuideCrossFire Bridge Driver Installation and Setup For Windows XP OSFor Windows 7 / VistaTM OS Page AMD Dual Graphics Operation Guide Enjoy the benefit of AMD Dual GraphicsWhat does an AMD Dual Graphics system include? AMD Vision Engine Control Center Dual Monitor and Surround Display Features Dual Monitor FeatureSurround Display Feature For Windows XP / XP 64-bit OSWhat is HDCP? For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OSHdcp Function ASRock Smart Remote Installation Guide Advanced Super IO Configuration CIR Controller EnabledCIR sensors in different angles Jumpers Setup DescriptionOnboard Headers and Connectors Serial ATA2 ConnectorsConsumer Infrared Module Header Chassis Speaker Header CPU Fan Connectors ATX 12V Power ConnectorHdmispdif Header Hdmispdif header, providing What is Hot Swap Function? Serial ATA Sata / Serial ATA2 SATA2 Hard Disks InstallationWhat is Hot Plug Function? Hot Plug and Hot Swap Functions for Sata / SATA2 HDDsSata / Sataii HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a Sata / Sataii HDD How to Hot Unplug a Sata / Sataii HDDDriver Installation Guide Installing Windows XP / XP 64-bit With RAID FunctionsSet up Uefi Use RAID Installation Guide to set RAID configuration Installing Windows XP / XP 64-bit Without RAID Functions Page Introduction Uefi Menu BarNavigation Keys Tab Enter Navigation KeysMain Screen F10 F12OC Tweaker Screen RAS# to CAS# Delay tRCD Dram Configuration Dram FrequencyDram Timing Control Power Down Enable CPU VoltageRAS to RAS Delay tRRD Command Rate CRWrite Recovery Time tWR Write to Read Delay tWTRWould you like to save current setting user defaults? SB VoltageAdvanced Screen Instant FlashCstate Pmin Mode CPU ConfigurationCore C6 Mode Cool ‘n’ QuietShare Memory North Bridge ConfigurationPrimary Graphics Adapter Onboard Hdmi HD AudioFront Panel South Bridge ConfigurationOnboard HD Audio Onboard LANSata IDE Combined Mode Storage ConfigurationSata Mode Sata ControllerSerial Port Address Super IO ConfigurationSerial Port Infrared PortAcpi Configuration Acpi Hpet table USB Configuration USB 2.0 ControllerLegacy USB Support Chassis Fan 2 Setting CPU Fan 1 SettingChassis Fan 1 Setting Hardware Health Event Monitoring ScreenBoot Screen Security Screen Save Changes and Exit Load Uefi DefaultsExit Screen Discard Changes and ExitRunning The Support CD Install Operating SystemSupport CD Information Drivers MenuInstalling OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Drv4E CtrlB5 LangengChoose Usable Physical Drive List to select Raid HDD Page Windows VistaTM 64-bit Page Windows 7 64-bit
Related manuals
Manual 76 pages 63.46 Kb