ASRock A75M-DGS manual ASRock Smart Remote Installation Guide

Page 23

2.7 ASRock Smart Remote Installation Guide

ASRock Smart Remote is only used for ASRock motherboard with CIR header. Please refer to below procedures for the quick installation and usage of ASRock Smart Remote.

Step1. Find the CIR header located next to the USB 2.0 header on ASRock motherboard.

Step2. Connect the front USB cable to the USB 2.0 header (as below, pin 1-5) and the CIR header. Please make sure the wire assignments and the pin assignments are matched correctly.

USB 2.0 header (9-pin, black) CIR header (4-pin, gray)

USB_PWR

P-

P+

GND DUMMY

1 2 3 4 5

GND

IRTX

IRRX

ATX+5VSB

Step3.

Install Multi-Angle CIR Receiver to the front USB port.

Step4.

Boot up your system. Press <F2> or <Del> to enter BIOS Setup Utility.

 

Make sure the option "CIR Controller" is setting at [Enabled].

 

(Advanced -> Super IO Configuration -> CIR Controller -> [Enabled])

 

 

 

If you cannot find this option, please shut down your system and install

 

Multi-Angle CIR Receiver to the other front USB port then try again.

 

 

Step5.

Enter Windows. Execute ASRock support CD and install CIR Driver. (It is

 

listed at the bottom of driver list.)

23

Image 23
Contents A75M-DGS Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Support CD ConnectorBios Feature USBPage ASRock Instant Flash Unique FeaturesASRock Extreme Tuning Utility Axtu ASRock Instant BootASRock XFast RAM ASRock APP ChargerASRock XFast USB ASRock XFast LANASRock Restart to Uefi ASRock Fast BootATXPWR1 Motherboard LayoutLAN Port LED Indications I/O PanelPre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationInstalling a Dimm Installation of Memory Modules DimmExpansion Slots PCI and PCI Express Slots Installing an expansion cardWhat does an AMD Dual Graphics system include? AMD Dual Graphics Operation GuideEnjoy the benefit of AMD Dual Graphics AMD Vision Engine Control Center Dual Monitor Feature Dual Monitor and Surround Display FeaturesFor Windows XP / XP 64-bit OS Surround Display FeatureHdcp Function What is HDCP?Advanced Super IO Configuration CIR Controller Enabled ASRock Smart Remote Installation GuideCIR sensors in different angles Description Jumpers SetupOnboard Headers and Connectors Infrared Module Header Pwrbtn Power Switch CPU Fan ConnectorsPlease connect an ATX power supply to this connector ATX Power ConnectorHot Plug and Hot Swap Functions for SATA3 HDDs Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? What is Hot Swap Function?Points of attention, before you process the Hot Plug SATA3 HDD Hot Plug Feature and Operation GuideHow to Hot Unplug a SATA3 HDD How to Hot Plug a SATA3 HDDSet up Uefi Driver Installation GuideInstalling Windows XP / XP 64-bit With RAID Functions \ RAID Installation Guide Make a SATA3 Driver Diskette Use RAID Installation Guide to set RAID configurationInstalling Windows XP / XP 64-bit Without RAID Functions Page Uefi Menu Bar IntroductionF10 F12 Navigation KeysMain Screen Navigation Keys Tab EnterOC Tweaker Screen CPU Voltage Dram Timing Configuration Dram FrequencyDram Timing Control Power Down Enable RAS# to CAS# Delay tRCDWrite to Read Delay tWTR Command Rate CRWrite Recovery Time tWR RAS to RAS Delay tRRDInstant Flash Would you like to save current setting user defaults?Advanced Screen Cool ‘n’ Quiet CPU ConfigurationCore C6 Mode Cstate Pmin ModeOnboard Hdmi HD Audio North Bridge ConfigurationPrimary Graphics Adapter Share MemoryOnboard LAN South Bridge ConfigurationOnboard HD Audio Front PanelHard Disk S.M.A.R.T Storage ConfigurationSata Mode Sata ControllerSuper IO Configuration Acpi Configuration Acpi Hpet table Legacy USB Support USB ConfigurationUSB 2.0 Controller USB 3.0 ControllerHardware Health Event Monitoring Screen CPU Fan 1 SettingChassis Fan 1 Setting Bootup Num-Lock Boot ScreenFast Boot Setup Prompt TimeoutAddOn ROM Display Boot From Onboard LANBoot Failure Guard Boot Failure Guard CountSecurity Screen Secure BootDiscard Changes and Exit Load Uefi DefaultsExit Screen Save Changes and ExitDrivers Menu Install Operating SystemSupport CD Information Running The Support CDInstalling OS on a HDD Larger Than 2TB Drv4E CtrlB5 Langeng Installing OS on a HDD Larger Than 2TB in RAID ModeChoose Usable Physical Drive List to select Raid HDD Page Windows VistaTM 64-bit Page Windows 8 64-bit / 7 64-bit