ASRock E35LM1 manual System Panel Header

Page 21

1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2.If you use AC’97 audio panel, please install it to the front panel audio header as below:

A.Connect Mic_IN (MIC) to MIC2_L.

B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C.Connect Ground (GND) to Ground (GND).

D.MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.

E.To activate the front mic.

For Windows® XP / XP 64-bit OS:

Select “Mixer”. Select “Recorder”. Then click “FrontMic”. For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:

Go to the "FrontMic" Tab in the Realtek Control panel. Adjust “Recording Volume”.

System Panel Header

This header accommodates

(9-pin PANEL1)

several system front panel

(see p.11 No. 8)

functions.

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the sys- tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.

21

Image 21
Contents E35LM1 Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Unique Feature Bios FeatureSupport CD See CautionPage Page Page Motherboard Layout I/O Panel LAN Port LED IndicationsTable for Audio Output Connection Page Installation Pre-installation PrecautionsScrew Holes Installing a Dimm Installation of Memory Modules DimmInstalling an expansion card Expansion Slot PCI Express SlotPcie slot Advanced Super IO Configuration CIR Controller Enabled ASRock Smart Remote Installation GuideCIR sensors in different angles Description Jumpers SetupSerial ATA3 Connectors Onboard Headers and ConnectorsSystem Panel Header Please connect an ATX power supply to this connector ATX Power ConnectorSerial ATA3 SATA3 Hard Disks Installation What is Hot Plug Function?Hot Plug Function for SATA3 HDDs Points of attention, before you process the Hot Plug How to Hot Plug a Sata / Sataii / SATA3 HDD Driver Installation Guide Installing Windows XP / XP 64-bit Without RAID FunctionsInstall Windows XP / XP 64-bit OS on your system Page Uefi Setup Utility IntroductionUefi Menu Bar Main Screen Navigation KeysOC Tweaker Screen Dram Timing Control Power Saving ModeDram Timing Configuration Dram Frequency Bank InterleavingCommand Rate CR RAS# to CAS# Delay tRCDWrite Recovery Time tWR RAS to RAS Delay tRRDVoltage Configuration Dram Voltage User DefaultFCH Voltage +1.8V VoltageAdvanced Screen Instant FlashInternet Flash SVM Mode CPU ConfigurationC6 Mode Cool ‘n’ QuietNorth Bridge Configuration Primary Graphics AdapterShare Memory South Bridge Configuration Sata Mode Storage ConfigurationSata Controller Aggressive Link PM CapabilitySerial Port Super IO ConfigurationSerial Port Address CIR ControllerAcpi Configuration OMG Online Management Guard USB Configuration USB 2.0 ControllerLegacy USB Support Chassis Fan 1 Setting CPU Fan SettingChassis Fan 2 Setting Hardware Health Event Monitoring ScreenBoot Screen Security Screen Exit Screen Software Support Installing OS on a HDD Larger Than 2TB
Related manuals
Manual 119 pages 43.33 Kb