ASRock FM2A75M-ITX R2.0 manual Consumer Infrared Module Header

Page 30

Consumer Infrared Module Header

This header can be used to

(4-pin CIR1)

connect the remote

(see p.14 No. 11)

controller receiver.

Front Panel Audio Header

 

 

GND

(9-pin HD_AUDIO1)

 

 

 

 

PRESENCE#

 

 

 

 

 

 

MIC_RET

 

 

 

 

 

 

 

 

 

 

 

OUT_RET

(see p.14 No. 21)

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT2_L

 

 

 

 

 

 

 

 

J_SENSE

 

 

 

 

 

 

 

OUT2_R

 

 

 

 

 

MIC2_R

 

 

 

MIC2_L

This is an interface for the front panel audio cable that allows convenient connection and control of audio devices.

1.High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2.If you use AC’97 audio panel, please install it to the front panel audio header as below:

A.Connect Mic_IN (MIC) to MIC2_L.

B.Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C.Connect Ground (GND) to Ground (GND).

D.MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.

E.To activate the front mic.

For Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Go to the “FrontMic” Tab in the Realtek Control panel. Adjust “Recording Volume”.

System Panel Header

This header accommodates

(9-pin PANEL1)

several system front panel

(see p.14 No. 8)

functions.

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may con- figure the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to per- form a normal restart.

30

Image 30
Contents FM2A75M-ITX R2.0 Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Rear Panel I/O ConnectorBios Feature USBMonitor Support CDHardware CertificationsPage ASRock Instant Boot Unique FeaturesASRock Extreme Tuning Utility Axtu ASRock Instant FlashASRock XFast LAN ASRock APP ChargerASRock XFast USB ASRock XFast RAMASRock Internet Flash ASRock Crashless BiosASRock OMG Online Management Guard ASRock Uefi System BrowserASRock Dehumidifier Function ASRock Easy RAID InstallerASRock Fast Boot ASRock Interactive UefiMotherboard Layout ATXPWR1Panel LAN Port LED IndicationsTable for Audio Output Connection Page Installation Pre-installation PrecautionsCPU Installation Installation of CPU Fan and HeatsinkInstallation of Memory Modules Dimm Installing a DimmInstalling an expansion card Expansion Slot PCI Express SlotAMD Dual Graphics Operation Guide Enjoy the benefit of AMD Dual GraphicsWhat does an AMD Dual Graphics system include? AMD Vision Engine Control Center Dual Monitor and Surround Display Features Dual Monitor FeatureSurround Display Feature What is HDCP? Hdcp FunctionASRock Smart Remote Installation Guide Advanced Super IO Configuration CIR Controller EnabledCIR sensors in different angles Jumpers Setup DescriptionOnboard Headers and Connectors Serial ATA3 ConnectorsConsumer Infrared Module Header CPU Fan Connectors Pled System Power LEDATX 12V Power Connector Please connect an ATX What is Hot Swap Function? Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? Hot Plug and Hot Swap Functions for SATA3 HDDsSATA3 HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a SATA3 HDD How to Hot Unplug a SATA3 HDDDriver Installation Guide Set up UefiUse RAID Installation Guide to set RAID configuration Page Introduction Uefi Menu BarNavigation Keys + / Tab Enter Pgup Pgdn Home Navigation KeysMain Screen F10 F12OC Tweaker Screen Boost Frequency Multiplier Dram Timing Configuration Dram FrequencyMultiplier/Voltage Change CPU Frequency MultiplierDram Timing Control Dram Slot Power Down EnableVoltage Configuration Dram Voltage Dram Timing ControlAdvanced Screen Package C6 Mode CPU ConfigurationCore C6 Mode Cool ‘n’ QuietShare Memory North Bridge ConfigurationPrimary Graphics Adapter Dual GraphicsSouth Bridge Configuration Storage Configuration Acpi Configuration A75 USB 3.0 Controller USB ConfigurationUSB 2.0 Controller Legacy USB SupportSound Effect Uefi Update Utility Instant FlashTool System BrowserInternet Flash Network Configuration Internet SettingDehumidifier CPU Fan Setting Uefi Download ServerWould you like to save current setting user defaults? Hardware Health Event Monitoring Screen Setup Prompt Timeout Boot ScreenFast Boot Bootup Num-LockBoot Failure Guard Count Boot From Onboard LANBoot Failure Guard Full Screen LogoSecure Boot Security ScreenSave Changes and Exit Load Uefi DefaultsExit Screen Discard Changes and ExitRunning The Support CD Install Operating SystemSupport CD Information Drivers MenuInstalling OS on a HDD Larger Than 2TB Installing OS on a HDD Larger Than 2TB in RAID Mode Drv4E CtrlB5 LangengChoose Usable Physical Drive List to select Raid HDD Page Windows VistaTM 64-bit Page Windows 8 64-bit / 7 64-bit