ASRock Z77 Pro4 manual Surround Display Feature, For Windows XP / XP 64-bit OS

Page 28

Surround Display Feature

This motherboard supports surround display upgrade. With the internal VGA output support (DVI-D, D-Sub and HDMI) and external add-on PCI Express VGA cards, you can easily enjoy the benefits of surround display feature.

Please refer to the following steps to set up a surround display environment:

1.Install the PCI Express VGA cards on PCIE2 and PCIE3 slots. Please refer to page 22 for proper expansion card installation procedures.

2.Connect a DVI-D monitor cable to the DVI-D port on the I/O panel, connect a D-Sub monitor cable to the D-Sub port on the I/O panel and connect a HDMI monitor cable to the HDMI port on the I/O panel. Then connect other monitor cables to the corresponding connectors of the add-on PCI Express VGA cards on PCIE2 and PCIE3 slots.

3.Boot your system. Press <F2> or <Del> to enter UEFI setup. Enter “Share Memory” option to adjust the memory capability to [32MB], [64MB], [128MB], [256MB] or [512MB] to enable the function of D-sub. Please make sure that the value you select is less than the total capability of the system memory. If you do not adjust the UEFI setup, the default value of “Share Memory”, [Auto], will disable D-Sub function when an add-on VGA card is inserted to this motherboard.

4.Install the onboard VGA driver and the add-on PCI Express VGA card driver to your system. If you have installed the drivers already, there is no need to install them again.

5.Set up a multi-monitor display.

For Windows® XP / XP 64-bit OS:

Right click on desktop, choose “Properties”, and select the “Settings” tab so that you can adjust the parameters of the multi-monitors according to the steps below.

A.Click the “Identify” button to display a large number on each monitor.

B.Right-click the display icon in the Display Properties dialog that you wish to be your primary monitor, and then select “Primary”. When you use multiple monitors with your card, one monitor will always be Primary, and all additional monitors will be designated as Secondary.

C.Select the display icon identified by the number 2.

D.Click “Extend my Windows desktop onto this monitor”.

E.Right-click the display icon and select “Attached”, if necessary.

F.Set the appropriate “Screen Resolution” and “Color Quality” for the second monitor. Click “Apply” or “OK” to apply these new values.

G.Repeat steps C through E for the display icon identified by the numbers three to seven.

28

Image 28
Contents Z77 Pro4 Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Rear Panel I/O AudioUSB3.0 Unique Feature Support CDMonitor HardwareCertifications Page Page Page Motherboard Layout LAN Port LED Indications I/O PanelTable for Audio Output Connection Page Pre-installation Precautions Screw HolesCPU Installation Page Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Dual Channel Memory ConfigurationInstalling a Dimm Installing an expansion card Expansion Slots PCI and PCI Express SlotsInstalling Two CrossFireXTM-Ready Graphics Cards CrossFireXTM and Quad CrossFireXTM Operation GuideCrossFire Bridge For Windows XP OS Driver Installation and SetupFor Windows 7 / VistaTM OS Page Dual Monitor and Surround Display Features Dual Monitor FeatureSurround Display Feature For Windows XP / XP 64-bit OSFor Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS What is HDCP?Hdcp Function ASRock Smart Remote Installation Guide CIR sensors in different anglesJumpers Setup DescriptionOnboard Headers and Connectors USB 3.0 Header Besides two default USB System Panel Header Chassis Speaker Header Please connect the chassis ATX Power Connector ATX 12V Power Connector Please connect an ATXSerial port Header Serial ATA Sata / Serial ATA2 SATA2 Hard Disks Installation Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? What is Hot Swap Function?Hot Plug and Hot Swap Functions for Sata / SATA2 HDDs Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug How to Hot Plug a Sata / SATA2 / SATA3 HDD Set up Uefi Driver Installation GuideUse RAID Installation Guide to set RAID configuration Installing Windows XP / XP 64-bit Without RAID Functions Install Windows XP / XP 64-bit OS on your systemPage Introduction Uefi Menu BarNavigation Keys Main ScreenNavigation Keys + / Tab Enter Pgup Pgdn Home F10 F12OC Tweaker Screen Long Duration Power Limit Short Duration Power LimitDram Timing Configuration Load XMP Setting Intel Turbo Boost TechnologyCommand Rate CR Dram Timing Control Dram tCLDram tRCD Dram tRPMRC Fast Boot Voltage Configuration CPU Core VoltageDram tRTP Dram tFAWUser Defaults Advanced Screen Instant FlashCPU Configuration Hardware Prefetcher Intel Virtualization TechnologyAdjacent Cache Line Prefetch North Bridge Configuration South Bridge Configuration IntelR Rapid Start Technology IntelR Rapid Start TechnologyIntelR Smart Connect Technology IntelR Smart Connect TechnologyStorage Configuration Page Super IO Configuration Serial PortSerial Port Address Infrared PortAcpi Configuration USB Configuration USB 2.0 ControllerUSB 3.0 Controller Legacy USB SupportCPU Fan 1 & 2 Setting Chassis Fan 1 SettingChassis Fan 2 Setting Over Temperature ProtectionBoot Screen Security Screen Exit Screen Software Support Installing OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Windows VistaTM 64-bit Page Windows 7 64-bit
Related manuals
Manual 209 pages 16.35 Kb