ASRock X79 Extreme9 manual ASRock Smart Remote Installation Guide, CIR sensors in different angles

Page 45

2.11 ASRock Smart Remote Installation Guide

ASRock Smart Remote is only used for ASRock motherboard with CIR header. Please refer to below procedures for the quick installation and usage of ASRock Smart Remote.

Step1. Find the CIR header located next to the USB 2.0 header on ASRock motherboard.

USB 2.0 header (9-pin, black) CIR header (4-pin, gray)

Step2. Connect the front USB cable to the USB 2.0 header (as below, pin 1-5) and the CIR header. Please make sure the wire assignments and the pin assignments are matched correctly.

USB_PWR

P-

P+

GND DUMMY

1 2 3 4 5

GND

IRTX

IRRX

ATX+5VSB

Step3. Install Multi-Angle CIR Receiver to the front USB port. If Multi-Angle CIR Receiver cannot successfully receive the infrared signals from MCE Remote Controller, please try to install it to the other front USB port.

3 CIR sensors in different angles

1.Only one of the front USB port can support CIR function. When the CIR function is enabled, the other port will remain USB function.

2.Multi-Angle CIR Receiver is used for front USB only. Please do not use the rear USB bracket to connect it on the rear panel. Multi-Angle CIR Receiver can receive the multi-direction infrared signals (top, down and front), which is compatible with most of the chassis on the market.

3.The Multi-Angle CIR Receiver does not support Hot-Plug function. Please install it before you boot the system.

*ASRock Smart Remote is only supported by some of ASRock motherboards. Please refer to ASRock website for the motherboard support list: http://www.asrock.com

45

Image 45
Contents X79 Extreme9 Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Smart Switch ConnectorRear Panel I/O USB3.0Unique Feature Bios FeatureSupport CD HardwarePage Page Page Motherboard Layout LAN Port LED Indications I/O PanelASRock Game Blaster Off No Link Blinking Data Activity Input Features Output FeaturesScrew Holes Pre-installation PrecautionsCPU Installation Locate Pin1 and the two orientation key notches Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Notch break Break Installing a DimmExpansion Slots PCI Express Slots Pcie Slot ConfigurationsInstalling an expansion card Windows VistaTM 32-bit / 64-bit or Windows 7 32-bit / 64-bit ASRock Game Blaster Configuration Acoustic Echo Cancellation Select a recording device Mic VolumeMic Boost CrystalVoiceOptional Speakers Center Speakers / Headphones ConfigurationSubwoofer Rear pairMixer Equalizer Jack SetupEX Surround Device ConnectedStereo and Microphone Stereo and Line-InPlay stereo mix to digital output Advanced FeaturesUser Profiles ProfileRequirements SLITM, 3-Way Slitm and Quad Slitm Operation GuideASRock SLIBridge2S Card Two Goldfingers Installing Three SLITM-Ready Graphics CardsFor Windows XP / XP 64-bit OS For Slitm mode only Driver Installation and SetupSelect Control Panel tab Select Nvidia Control Panel tabPage Page CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards For Windows 7 / VistaTM OS For Windows XP OS\ Surround Display Information Surround Display FeatureCIR sensors in different angles ASRock Smart Remote Installation GuideASRock XFast Charger Operation Guide Description Jumpers SetupSerial ATA Sata Data Cable Onboard Headers and ConnectorsTwo USB 3.0 headers on this Infrared Module Header This header supports an CPU Fan Connectors ATX 12V Power Connector ATX Power ConnectorInstallation Guide of Rear USB 3.0 Bracket Installation Guide of Front USB 3.0 PanelSmart Switches Status Code Description 16 Dr. DebugPage Page Page Serial ATA3 SATA3 Hard Disks Installation Serial ATA Sata / Serial ATA2 SATA2 Hard Disks InstallationWhat is Hot Swap Function? What is Hot Plug Function?Hot Plug and Hot Swap Functions for Sata / SATA2 HDDs Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug How to Hot Plug a Sata / SATA2 / SATA3 HDD Driver Installation Guide Set up UefiUse RAID Installation Guide to set RAID configuration Install Windows XP / XP 64-bit OS on your system Installing Windows XP / XP 64-bit Without RAID FunctionsPage Teaming Function Operation Guide Click Expert ModePage Page From Control Panel, double-clickNetwork Connections Untied Overclocking TechnologyUefi Menu Bar IntroductionMain Screen Navigation KeysNavigation Keys F10OC Tweaker Screen Dram Timing Control Load XMP Setting Turbo Boost Power LimitCore Current Limit Additional Turbo VoltageDram Power Down Mode Command Rate CRDram tRCD Dram tRPODT NOM CH D Memory Power Savings ModeLoad Power Saving Mode Voltage Control Voltage Configuration CPU Core VoltageUser Default CPU Load-Line CalibrationInstant Flash Advanced ScreenCPU Configuration Enhance Halt State C1E CPU Thermal ThrottlingCPU C3 State Support CPU C6 State SupportNorth Bridge Configuration South Bridge Configuration Onboard Debug Port LED Good Night LEDStorage Configuration Serial Port Super IO ConfigurationSerial Port Address Infrared PortAcpi Configuration USB 2.0 Controller USB ConfigurationUSB 3.0 Controller Legacy USB SupportME Subsystem Intel ME Subsystem Configuration ME VersionHardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Software Support Installing OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Windows VistaTM 64-bit Page Windows 7 64-bit