MSI Z77A-G43 manual Boot, Save & Exit

Page 49

MS-7758

Resume By PCI or PCI-E Device

When set to [Enabled], the feature allows your system to be awakened from the power saving modes through any event on PCI/ PCIe device.

Resume From S3 by USB Device

The item allows the activity of the USB device to wake up the system from S3 (Sus- pend to RAM) sleep state.

Resume From S3/S4/S5 by PS/2 Mouse/ Keyboard

These items determine whether the system will be awakened from what power sav- ing modes when input signal of the PS/2 mouse/ keyboard is detected.

Boot

Full Screen Logo Display

[Enabled] The OS boots straight to the GUI without showing the POST screen, [Disabled] Shows the POST messages at boot.

== Boot Option Priorities==

1st~9th Boot

These items are used to prioritize the installed boot devices.

USB KEY Drive BBS Priorities/ UEFI Boot Drive BBS Priorities

1st~8th Boot

These items are used to prioritize the installed USB key drives/ UEFI boot drives.

Save & Exit

Discard Changes and Exit

This it is used to abandon all changes and exit setup.

Save Changes and Reboot

This item is used to save changes and reboot the system.

Save Changes

This item is used to save changes.

Discard Changes

This item is used to abandon all changes.

Restore Defaults

This item is used to load the optimized default values set by the BIOS vendor. == Boot Override ==

The installed storage devices will appear on this menu, you can select one of them be a boot device.

Built-in EFI Shell

Use this item to enter the EFI Shell.

Chapter 2

2-9

Image 49
Contents MS-7758 v1.x Mainboard ZH77A-G43/ Z77A-G43 seriesRevision History Preface FCC-B Radio Frequency Interference Statement Bsmi EMI 聲明 Weee Waste Electrical and Electronic Equipment Statement Español Türkçe Contents Appendix a Realtek Audio Getting Started Optional Accessories Packing ContentsChapter Assembly PrecautionsProcessor Support Mainboard SpecificationsForm Factor Connectors Quick Guide Connectors Reference Guide LAN Back Panel Quick GuideHDMI+DVI DVI+VGA VGA+HDMI Introduction to the LGA 1155 CPU CPU Central Processing UnitCPU & Cooler Installation SATA2 SATA1 SATA4 SATA3 SATA6 SATA5 Mainboard Hook Mounting Screw Holes JPWR1 ATX 24-pin Power Connector Power SupplyJPWR2 ATX 8-pin Power Connector Memory Dual -Channel mode Population RuleInstalling Memory Modules PCIE1~E4 PCIe Expansion Slot Expansion SlotsPCI1~3 PCI Expansion Slot Video/ Graphics Cards Single Video Card InstallationPCI Interrupt Request Routing AMD CrossFire Multi -GPU Technology Chapter SATA1~6 Sata Connectors Internal ConnectorsCPUFAN,SYSFAN1~4 Fan Power Connectors JFP1, JFP2 Front Panel Connectors USB 3.0 Bracket optional JUSB3 USB 3.0 Expansion ConnectorJCI1 Chassis Intrusion Connector JUSB1~2 USB 2.0 Expansion ConnectorsJTPM1 TPM Module Connector JAUD1 Front Panel Audio ConnectorJLPT1 Parallel Port Connector JCOM1 Serial Port ConnectorJTURBO1 MultiConnect Panel Connector optional JDLED3 Voice Genie Connector optionalJBAT1 Clear Cmos Jumper JumperBios Setup Entering Press DEL key to enter Setup Menu, F11 to enter Boot MenuOverview Boot device priority bar Sub-Menu OperationGeneral Help System Status SettingsPcie GEN3 AdvancedHpet Occurred Save & Exit BootEist Chapter Page MEMORY-Z Page ECO Browser Installing WinkiUtilities Page Updating the Bios with Live Update Security Realtek Audio Installation for Windows Installing the Realtek HD Audio DriverSoftware panel overview Software ConfigurationAuto popup dialog Ix a Append Hardware Default SettingBackpanel audio jacks to 8-channel speakers diagram Intel RAID Introduction Ix B Append Using Intel Rapid Storage Technology Option ROMXXX.X GB RAID array by using the upper arrow XXXX-XXXXXXXX Press Y key to accept the volume deletion XXXX-XXXXXXXX Recovery Volume Options Installing Driver Ix B Append Main Menu Degraded RAID ArrayIx B Append System Acceleration optional Ix B Append Disk Port RST Synchronization optional