MSI Z87-MPOWER-MAX manual Accordingly, Power-saving in halt state, Then C0

Page 92

Chapter 3

▶Intel C-State [Auto]

C-state is a processor power management technology defined by ACPI.

[Auto]

This setting will be configured automatically by BIOS.

[Enabled]

Detects the idle state of system and reduce CPU power consumption

 

accordingly.

[Disabled]

Disable this function.

▶C1E Support [Disabled]

Enables or disables the C1E function for power-saving in halt state. This item appears when "Intel C-State" is enabled.

[Enabled]

Enables C1E function to reduce the CPU frequency and voltage for

 

power-saving in halt state.

[Disabled]

Disables this function.

▶Package C State limit [Auto]

This item allows you to select a CPU C-state mode for power-saving when system is idle. This item appears when "Intel C-State" is enabled.

[Auto]

This setting will be configured automatically by BIOS.

[C0~C7s]

The power-saving level from high to low is C7s, C7, C6, C3, C2,

 

then C0.

[No limit]

No C-state limit for CPU.

▶LakeTiny Feature [Disabled]

Enables or disables Intel Lake Tiny technology with iRST for SSD. This item appears when “Intel C-State” is enabled.

[Enabled]

Enhance the dynamic IO load adjusted performance for accelerating

 

the SSD speed.

[Disabled]

Disables this feature.

Note: The following items will appear when "Intel Turbo Boost " is enabled.

▶Long Duration Power Limit (W) [Auto]

Sets the long duration TDP power limit for CPU in Turbo Boost mode.

▶Long Duration Maintained (s) [Auto]

Sets the maintaining time for "Long duration power Limit(W)".

▶Short Duration Power Limit (W) [Auto]

Sets the short duration TDP power limit for CPU in Turbo Boost mode.

▶CPU Current limit (A) [Auto]

Sets maximum current limit of CPU package in Turbo Boost mode. When the current is over the specified limit value, the CPU will automatically reduce the core frequency for reducing the current.

▶1/2/3/4-Core Ratio Limit [Auto]

These items only appear when a CPU that support this function is installed. These items allow you to set the CPU ratios for different number of active cores in turbo boost mode. These items appear when the installed processor supports this function.

BIOS Setup

3-24

Image 92
Contents Preface G52-78151X1Preface Smartphone Application Technical Support IiiSafety Instructions CE Conformity 無線設備警告聲明 工作頻率2.412GHz~2.462GHz該頻段限於室內使用。クラス B 情報技術装置 この製品は、周波数帯域 2.412GHz~2.484GHz で動作しているときは、屋内において のみ使用可能です。European Union ViiWeee Waste Electrical and Electronic Equipment Statement Hinweis von MSI zur Erhaltung und Schutz unserer UmweltEspañol Türkçe Contents FV1 V-Check Connectors Check Spots Bios LEDsOC Switch LEDs Debug Code LED Table Total InstallerBios Setup XiiiPage Chapter Packing Contents Optional AccessoriesMotherboard ShieldAssembly Precautions Motherboard Specifications Supports Intel Wireless Display WiDi 1x GO2BIOS button1x Power button 1x Reset buttonWi-Fi BluetoothCommand Center Live UpdateConnectors Quick Guide Connectors Reference Guide Back Panel Quick Guide HDMI+HDMI Introduction to the LGA 1150 CPU Golden triangle is the Pin 1 indicatorCPU Central Processing Unit CPU & Heatsink Installation Video DemonstrationChapter Chapter Dual -Channel mode Population Rule MemoryMounting Screw Holes LinePower Supply JPWR1~3 ATX Power ConnectorsPCIe 2.0 x1 Slot Expansion SlotsPCIE1~7 PCIe Expansion Slots Single Video Card Installation Video/ Graphics CardsAMD CrossFire Multi -GPU Technology Chapter Nvidia SLI Technology Choose this item Internal Connectors SATA1~6 Sata ConnectorsCPUFAN1~2,SYSFAN1~3 Fan Power Connectors JFP1, JFP2 System Panel Connectors JUSB1~2 USB 2.0 Expansion Connector JUSB3~4 USB 3.0 Expansion Connectors JCI1 Chassis Intrusion ConnectorMSATA slot is for mSATA interface solid state drives SSD JAUD1 Front Panel Audio ConnectorMSATA1 mSATA Slot FV1 V-Check Connectors Voltage CheckpointsOverclocking performance Lower memory timings may require higher voltages toCheck Spots Off ButtonsOC1 OC Genie Button POWER1 Power Button RESET1 Reset ButtonSW- TACT1, SW- TACT2 Base Clock Control Buttons Plus button Minus button Base clock + 1 MHzFASTB1 GO2BIOS Button Jumpers JBAT1 Clear Cmos JumperJDISCH1 Discharge Jumper Clear DataSwitch Multi Bios Switch Multi -BIOS SwitchOCSWITCH1 OC Genie Mode Switch LED Status Indicators Bios LEDsOC Switch LEDs Digit Debug Code LED Bios LEDs OC Switch LEDsDebug Code LED Table A8,A9,AB Start of Setup. Bios setup if needed/ requestedReady To Boot event/Legacy Boot event Total Installer Drivers and UtilitiesQuick Installation CPU Installation Quick InstallationQuick Installation Memory Installation Motherboard Installation Chapter Power Connectors Installation Chapter Sata HDD Installation MSATA SSD Installation Front Panel Audio Connector Installation Front Panel Connector InstallationJFP1 Connecotr Installation USB3.0 Connector Installation Peripheral Connector InstallationUSB2.0 Connector Installation Graphics Card Installation Chapter Bios Setup Entering Setup Entering Bios SetupPress DEL key to enter Setup Menu, F11 to enter Boot Menu Bios SetupOverview Bar Sub-menuOperation Settings System StatusDisabled AdvancedInstalled in the system ModeIntegrated Graphics Display PCI-Express Graphics DeviceEntry on S3 RTC Wake Enabled TechnologySSD speed Bios Save/RestoreEnables or disables the legacy USB support Requirement Before AC power lossRegulation Enabled Enables the PS2 devices during Post Boot settingsCustom Load the secure keysWhen activity or input signal of LAN device is detected Sleep state when activity of USB device is detectedDisabled Disables this function EventsBoot SecuritySave & Exit Make U-Key atThis setting will be configured automatically by Bios Next Boot Enables LC PLL for normal usageEnables SB PLL for extreme overclocking Disabled Disables this function Enhanced Turbo AutoProfile Dram Timing Mode Auto Selects the memory timing mode Detect of installed memory modulesBooting to accelerate the system booting time LinkPerformance ProtectionSerial Voltage Identification Over-current protection To load the default settings for new devices+ Allows you to set the positive offset voltage Electromagnetic Interference problem Disabled Enhances the overclocking ability of CPU Base clockEnabled Enables Intel AES support Disabled Adaptive temperatureProcessor with extended Cpuid value WormsThen C0 Power-saving in halt stateAccordingly Flash OC Profile Hardware Monitor SpeedChapter Appendix a Realtek Audio Software ConfigurationSoftware panel overview Auto popup dialog Hardware Default Setting Backpanel audio jacks to 4-channel speakers diagramBackpanel audio jacks to 6-channel speakers diagram Backpanel audio jacks to 8-channel speakers diagramPage Appendix B Introduction Intel RAIDUsing Intel Rapid Storage Technology Option ROM XXX.X GB Appendix B XXXX-XXXXXXXX Press Y key to accept the volume deletion Delete Volume VerificationXXXX-XXXXXXXX Recovery Volume Options Degraded RAID Array Main MenuAppendix B System Acceleration optional Appendix B Press S to synchronize data When prompted, press Y to confirmRST Synchronization optional