NuTone 62BK244CCN(X), 62BK244CMP, 62BK244TMP installation instructions Installation of Doors

MODEL:

	For help, call us toll
	free!
RECESSED	1-800-325-8351

Register your

INSTRUCTIONS

MODEL	WALL OPENING			OVERALL SIZE
NO.	W	H	D	W	H	D
62BK244CBK(X)	141/4	24	4	161/2 261/2 51/4
62BK244CCN(X)	141/4	24	4	161/2 261/2 51/4
62BK244CCY(X)	141/4	24	4	161/2 261/2 51/4
62BK244CMP	141/4	24	4	161/2 261/2 51/4
62BK244TBK(X)	141/4	24	4	161/2 261/2 51/4
62BK244TCY(X)	141/4	24	4	161/2	261/2	51/4
62BK244TGK(X)	141/4	24	4	161/2	261/2	51/4
62BK244TMP	141/4	24	4	161/2	261/2	51/4

INSTALLATION

1.	Carefully remove all
	packages, shelves and door aside
	and shelves are located in the fi llers identifi ed by
	Enclosed” tape.
2.	Determine desired location of cabinet on wall. Mark wall to
	show wall opening size (see dimension chart). Generally, the
	recommended height to the center of the cabinet is 64” from
	the fl oor. (Fig. 1)
3.	CAUTION: Wall studs, plumbing or electrical lines that

Fig. 1

Approx. 64" to Floor

D

W

H

Fig. 2

Insert screw through clear plastic base

interfere must be removed or relocated. Cut wall opening,

being careful not to damage the surrounding wall surface.

Insert framing to support all plaster board edges.

4. Prepare the mounting screws by placing the screws into the

plastic bases. (Fig. 2)

5. Note: For ease of installation, an additional person is

recommended. Insert cabinet into wall opening. (Fig.3)

Ensure the cabinet is plumb and level. If necessary use a

carpenter’s level and shim corners of cabinet. Secure to wall

studs through the four (4) mounting holes inside cabinet,

using the screws that have been placed into the plastic

bases. (Fig. 4) Do not over tighten the mounting screws as

the body side wall may bend and prevent proper shelf

Fig. 3

Cabinet

Body

Wall Opening

Fig. 4

Mounting

Screws

Mounting screw into mounting hole

installation. Only tighten screws until they are fl ush with the

body.

6. Snap the screw covers over the screw bases. (Fig.5)

INSTALLATION of DOORS

1.Remove hinges and screws from hardware bag. Mount hinge unit on door as shown in Fig. 6 securing with screws provided.

2.Install the door by inserting door side of the hinge into the bracket on the body shown in Fig. 7.

3.Check door for proper alignment. If the door needs to be adjusted please refer to the adjustment procedures in Fig. 8.

INSTALLATION of SHELVES, HOLE PLUGS AND BUMPERS

1.Select where you want the shelves to be placed.

2.Insert two (2) shelf brackets at each end of the shelf location. (Fig. 9).

3.Set shelves in place on the shelf brackets, pressing down on the shelf to lock in place. (Fig. 9).

4.Remove hole plugs from hardware bag and place in remaining holes. (Fig. 10).

5.Remove bumpers from hardware bag and position to body. (Refer to Service Parts Drawing - Key No. 9 for bumper locations).

Fig. 5		Fig. 6
		Hinge Mounted
Snap on Cover	Cover	to Door
Screw
	Base
Fig. 7	Hook bottom of	Fig. 8
			This screw for
	hinge into place
		Door Adjustment	up and down
Hinge Mounted	on the bracket
			adjustments
to Cabinet
		This screw
		for depth
		adjustments
Press down		This screw
on hinge until it
clips in place		for left and right
		adjustments
Fig. 9		Fig. 10