Lennox International Inc LB-83114C, 61H42 Timing Jumper, Test Mode Control Timings

Page 3

The defrost control is a solid state control manufacturedby Hamilton Standard.The control providesautomaticswitchingfrom normalheating operationto defrost mode and back.The defrost controlcontainsasolidstatetimerwhichswitchesan

externa] defrost relay through 1/4" male spades mountedon the control'scircuit board.Thecontrol

energizesthedefrostrelayat regular timed intervals.

On some units, a normally open defrost switch placed in series between the defrost relay and the control initiates defrost only when needed at the end of the timed intervals. On other units, the control initiates defrost on demand from the defrost thermostat,

7- Timing Jumper

A factory installed jumper on the circuit board connects terminal Wl on the circuit board to one

of the three timing pins. 8- TST Pins

Each board is equipped with a test pins for use in

troubleshooting the unit. When jumpered together, these pins reduce the control timing to about 1/256 original time.

ACAUTION

Defrost Control Components:

1- 24V Terminal

Terminat 24V receives 24VAC from the control transformer. This terminal powers the control's internal timer and relays. Terminal 24V must be powered at all times to provide HOLD between thermostat demands.

2 COM Terminal

Terminal COM provides 24VAC common. 3- HLD Terminal

Terminal HLD hold the internal timer in place between thermostat demands and altows the unit

to continue timing upon resumption of thermostat demand, tn most units, terminal HLD is connected directly to thermostat demand.

4- OUT Terminal

Terminal OUT controls unit defrost when connected to one side of the defrost relay coil. An internal relay connected to terminal OUT closes to allow external defrost relay to energize and initiate defrost. At the end of the defrost period, the internal relay connected to terminal OUT opens to de-energize the external defrost relay.

5- RST Terminal

This terminal is not functional for the specified application.

6- Timing Pins (T1,T2,T3)

Each of these pins provides a different timed interval between defrosts (30, 60 or 90 seconds). A jumper connects the pins to circuit board terminal Wl. To change the interval between defrosts, remove the jumper from the pin it is connected to and reconnect the jumper to one of the other available pins.

To Place Control in Test Mode:

1- Turn off all power to avoid damaging the circuit board.

2- Make sure all control terminats are connected as shown on unit wiring diagram before attempting to place control in test mode.

IMPORTANT

3- Connect jumper to "TST" pins,

4- Turn indoor thermostat to heat mode and adjust to highest temperature setting.

5- See table 1 for control timings in "TST" mode,

6- Turn on power to unit and re-adjust thermostat. Be sure to remove jumper when test is complete.

TABLE 1

TEST MODE CONTROL TIMINGS

NORMAL

!_ 30+3

60±6

:

90_9

_

14+1,4

OPERATION

MIN

MIN

i

MIN.

 

MIN.

"TST" PINS

1!7+0r7

14+1A

i

21_+21

 

3-3_0.3

 

 

JUMPERED

SEC.

i SEC

i

SEC*

i

SEC

TOGETHER

 

 

 

 

!

 

Page 3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Solid State Defrost Replacement Board Typical Wiring TOM9TOP View Front View Timing Jumper Test Mode Control TimingsDefrost Control Troubleshooting Flowchart YesStart Here

LB-83114C, 61H42 specifications

Lennox International Inc 61H42,LB-83114C is a prominent heating and cooling component that exemplifies high efficiency and reliability in temperature control for residential and commercial spaces. Known for its robust performance and superior design, this product is a critical part of Lennox's commitment to providing innovative HVAC solutions.

One of the main features of the 61H42,LB-83114C is its efficiency in energy consumption. The unit is designed to minimize power usage while still delivering powerful temperature control. This efficiency is not only beneficial for reducing utility bills but also makes it an environmentally friendly choice. The integration of advanced technology ensures that heating and cooling requirements are met with minimal energy waste.

The 61H42,LB-83114C leverages cutting-edge technologies such as variable speed operations and advanced microprocessor controls, which enhance its performance. These features allow the unit to adjust its operation based on real-time conditions, optimizing heating and cooling cycles according to the specific needs of the environment. This adaptability not only promotes comfort but also extends the longevity of the product.

In addition to efficiency and technology, the 61H42,LB-83114C is built with durability in mind. The materials used in its construction are resistant to wear and tear, ensuring long-term performance even in challenging climates. The product is further equipped with advanced insulation that minimizes noise and vibration, resulting in quieter operation that enhances the comfort of an indoor environment.

Another noteworthy characteristic is its smart compatibility. The unit can be integrated into modern smart home systems, allowing users to control their HVAC setup remotely. This feature provides added convenience and enhances user experience, as it allows for customized temperature settings and schedules tailored to the occupant's lifestyle.

In conclusion, Lennox International Inc 61H42,LB-83114C stands out as a notable choice for those seeking reliable and efficient climate control solutions. With its energy-efficient design, advanced technologies, durable construction, and smart compatibility, this HVAC component exemplifies Lennox's dedication to quality and innovation in the heating and cooling market. Whether for residential or commercial applications, the 61H42,LB-83114C demonstrates exceptional performance and reliability, making it a preferred option for many consumers.
Top Page Image Contents