Multiquip QP3TH manual Operation, Starting the Engine

Page 18

OPERATION

CAUTION

DO NOT attempt to start the engine unless the pump has previously been primed with water. Severe pump damage will occur if pump has not been primed.

STARTING THE ENGINE

1.Place the engine fuel valve lever (See Figure 7) to the ON position.

Figure 7. Engine Fuel Valve Lever (ON Position)

2.Move the throttle lever (See Figure 8) away from the slow position, about 1/3 of the way toward the fast position.

Figure 8. Throttle Lever (1/3 Start Position

3.Place the choke lever (See Figure 9) in the CLOSED position if starting a cold engine.

Figure 9. Engine Choke Lever (Closed)

4.Place the choke lever (See Figure 10) in the OPEN position if starting a warm engine or the temperature is warm.

Figure 10. Engine Choke Lever (Open)

5.Place the engine ON/OFF switch (See Figure 11) in the ON position.

Figure 11. Engine ON/OFF Switch (ON Position)

6.Grasp the starter grip (See Figure 12) and slowly pull it out.The resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly and smoothly for starting.

Figure 12. Starter Grip

7.If the engine has started and the choke lever was moved to the CLOSED position to start the engine, gradually move the choke lever to the OPEN position (Figure 13) as the engine warms up. If the engine has not started repeat steps 1 through 6.

PAGE 18 — QP3TH TRASH PUMP • OPERATION AND PARTS MANUAL — REV. #8 (01/29/14)

Image 18
Contents Model QP3TH This Manual Must Accompany the Equipment AT ALL TimesProposition 65 Warning QP3TH Trash Pump Operation and Parts Manual REV. #8 01/29/14 Table of Contents QP3TH Centrifugal PumpParts Ordering Procedures Ordering parts has never been easierSafety Information Safety Messages„ Never open the priming plug when pump General SafetyPump Safety Serious damage to the equipment or engineEngine Safety Fuel SafetyBefore servicing equipment Battery Safety Electric Start only Transporting Safety„ Use well-insulated gloves when picking up the battery Emissions Information Label must remain with the engine for its entire lifeDry Net Weight Specifications PumpSpecifications Pump ModelSpecifications Engine Specifications EnginesHonda GX240K1QA2 General Information Pump Components Discharge Port Connect a 3-inch discharge hose to this portBasic Engine Initial ServicingMuffler Used to reduce noise and emissions Oil Type Inspection EngineBefore Starting SeasonSetup Starting the Engine Place the engine ON/OFF switch See in the on positionOperation Place the engine fuel valve lever See to the on positionStopping the Engine Always run engine at full speed while pumpingPlace the fuel shut-off lever See in the OFF position Pump Cleaning Maintenance PumpAdjusting Impeller Clearance Pump Vacuum TestPump Vacuum Tester Engine Maintenance Schedule Maintenance EngineEngine Maintenance First EveryWeekly Engine AIR CleanerDaily Engine OILSpark Arrester Cleaning Spark Arrester RemovalStorage Pump StorageSymptom Possible Problem Solution Difficult to start Troubleshooting EngineEngine Troubleshooting Operation not satisfactoryTroubleshooting ENGINE/PUMP Pump TroubleshootingSymptom Possible Problem Solution Sample Parts List Explanation of Code in Remarks ColumnSuggested Spare Parts Qty DescriptionPump Assembly 1992100173 19921000111992100020 1992000110Pump Assembly 0151191257 01810908200181090825 M12 X 57 X15 XEngine Service Parts 17672Z4H000 17672ZE2W0117672-880-000 17620ZH7023Terms and Conditions of Sale Parts Freight PolicyQP3TH Trash Pump Operation and Parts Manual REV. #8 01/29/14 HERE’S HOW to GET Help