Limited Warranty

UPG warrants this product to be free from defects in factory workmanship and material under normal use and service and will, at its option, repair or replace any parts that prove to have such defects according to the terms outlined on this warranty. This warranty covers only the equipment described by the Product Model Number and Serial Number listed on the Warranty Registration Card.

For your benefit and protection, return the Warranty Registration Card to UPG promptly after installation. This will initiate the warranty period and allow us to contact you, should it become necessary. In the absence of a recorded Warranty Registration Card, the warranty period will begin upon product shipment from UPG.

This warranty extends only to the original consumer purchaser and is non-transferable. For this warranty to apply, the product must be installed according to UPG recommendations and specifications, and in accordance with all local, state, and national codes; and the product must not be removed from its place of original installation. The warranty period for repair or replacement parts provided hereunder shall not exceed beyond the warranty period stated below.

PREMIUM HUMIDIFIERS AND AIR CLEANERS

PARTS

5 yrs

UPG strongly recommends regular periodic preventative maintenance on this equipment. The person most familiar with the equipment in your HVAC system is a UPG dealer. The UPG dealer can ensure your maintenance program meets the conditions of the “UPG Warranty,” maximize the efficiency of the equipment, and service your unit within the mandated guidelines. This warranty applies only to products installed in the United States and Canada.

EXCLUSIONS

This warranty does not cover any:

1.Shipping, labor, or material charges.

2.Damages resulting from transportation, installation, or servicing.

3.Damages resulting from accident, abuse, fire, flood, alteration, or acts of God (tampering, altering, defacing or removing the product serial number will serve to void this warranty).

4.Damages resulting from use of the product in a corrosive atmosphere.

5.Damages resulting from inadequacy or interruption of electrical service or fuel supply, improper voltage conditions, blown fuses, or other like damages.

6.Cleaning or replacement of filters.

7.Damages resulting from failure to properly and regularly clean air and/or water side of condenser and evaporator.

8.Damages resulting from: (I) freezing of condenser water or condensate; (II) inadequate or interrupted water supply; (III) use of corrosive water; (IV) fouling or restriction of the water circuit by foreign material or like causes.

9.Damages resulting from operation with inadequate supply of air or water.

10.Damages resulting from use of components or accessories not approved by UPG (vent dampers, etc.).

11.Increase in fuel or electric cost.

12.Disposable humidifier pad which will have to be replaced from time to time depending on the amount of use.

13.Disposable media which will have to be replaced from time to time depending upon the amount of use.

14.Inner housing seal.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

SOME STATES DO NOT ALLOW THE DISCLAIMER OF IMPLIED WARRANTY, SO THAT THE ABOVE DISCLAIMER MAY NOT APPLY TO YOU.

SOME STATES ALLOW ONLY A PARTIAL LIMITATION ON IMPLIED WARRANTIES TO LIMIT THE DURATION OF IMPLIED WARRANTIES TO THE DURATION OF THE EXPRESS WARRANTY. IN SUCH STATES, THE DURATION OF IMPLIED WARRANTIES IS HEREBY EXPRESSLY LIMITED TO THE DURATION OF THE EXPRESS WARRANTY ON THE FACE HEREOF.

IN NO EVENT, WHETHER AS A RESULT OF BREACH OF WARRANTY OR CONTRACT, TORT (INCLUDING NEGLIGENCE) STRICT LIABILITY OR OTHERWISE, SHALL UPG BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OF USE OF THE EQUIPMENT OR ASSOCIATED EQUIPMENT, LOST REVENUES OR PROFITS, COST OF SUBSTITUTE EQUIPMENT OR COST OF FUEL OR ELECTRICITY. THE ABOVE LIMITATIONS SHALL INURE TO THE BENEFIT OF UPG’S SUPPLIERS AND SUBCONTRACTORS. THE ABOVE LIMITATION ON CONSEQUENTIAL DAMAGES SHALL NOT APPLY TO INJURIES TO PERSON’S IN THE CASE OF CONSUMER GOODS.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR FOR STRICT LIABILITY IN TORT, SO THAT THE ABOVE EXCLUSIONS AND LIMITATIONS MAY NOT APPLY TO YOU.

UPG DOES NOT ASSUME, OR AUTHORIZE ANY OTHER PERSON TO ASSUME FOR UPG, ANY OTHER LIABILITY FOR THE SALE OF THIS PRODUCT. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

For Owner’s Information:
PRODUCT MODEL NO._ ______________________________	INSTALLATION DATE__________________________________
UNIT SERIAL NO._ __________________________________	INSTALLING DEALER_ _________________________________
Subject to change without notice. Printed in U.S.A.
Copyright © by York International Corp. 2005. All rights reserved.

	Johnson Controls
572625-UUM-A-0310	Unitary Products	10008445 3.10
572625-UUM-A-0310	5005 York Drive, Norman, OK 73069	10008445 3.10
Supersedes 532647-UUM-A-0809	5005 York Drive, Norman, OK 73069	B2701125B

M10PAC1625/2020/2025, M13PAC1625/2020/2025 specifications

Johnson Controls is a global leader in building efficiency, energy solutions, and technology integration. Among its extensive product line, the M13PAC1625/2020/2025 and the M10PAC1625/2020/2025 series of controllers stand out for their innovative features and performance capabilities, designed to meet the evolving needs of modern building automation.

The M13PAC series is known for its robust processing power and adaptability. With its advanced microcontroller technology, the M13PAC1625/2020/2025 can handle complex control strategies, making it suitable for a wide range of applications. This series supports a variety of communication protocols, facilitating integration with existing building management systems. The flexibility of the M13PAC controllers allows them to efficiently manage HVAC systems, lighting, and security, promoting optimal energy usage throughout the building.

Similarly, the M10PAC series is engineered for reliability and scalability. The M10PAC1625/2020/2025 models feature a streamlined design that is easy to install and configure. Their compact form factor is ideal for applications with space constraints while still delivering the high-performance levels expected from Johnson Controls products. These controllers are equipped with intuitive user interfaces that simplify operations and enhance user experience.

Both series utilize advanced algorithms for predictive maintenance and energy optimization. This feature aids in identifying potential issues before they escalate, reducing downtime and maintenance costs. Additionally, the controllers employ real-time data analytics to monitor and adjust system performance continuously, ensuring that energy consumption is kept to a minimum without sacrificing comfort or productivity.

In terms of connectivity, both the M13PAC and M10PAC series support IoT integration, allowing users to remotely monitor and control building systems through mobile applications or web interfaces. This capability enhances operational efficiency and provides users with actionable insights into energy usage patterns and system performance.

With their emphasis on sustainability, the Johnson Controls M13PAC1625/2020/2025 and M10PAC1625/2020/2025 series reflect the company’s commitment to creating smarter, more energy-efficient buildings. By harnessing the latest technological advancements, these controllers not only enhance operational efficiency but also contribute to reduced carbon footprints and improved occupant comfort. As the demand for sustainable building solutions continues to grow, Johnson Controls remains at the forefront, driving innovation in building automation technology.