| g/REW/3, | |
| f/FF/4 | |
TUNER, BAND | L, STOP | |
a, REC | ||
DECK 1/2 | ||
c DECK1 | DECK2 c | |
| :, TAPE | |
| :/J, CD | |
DISC | CLOCK/TIMER | |
| ||
PROGRAM | Numbered | |
PLAY MODE | ||
buttons | ||
| ||
TUNER, BAND |
|
ALBUM (
or 
) 
g, REW/3, 
f, 4/FF
Radio
Automatic presetting
Do the following once each for FM and AM.
Preparation: Tune to the frequency where
Hold down [PROGRAM] until the frequency changes.
AK330
AK230
The tuner presets all the stations it can receive into the channels in ascending order. When finished, the last station memorized is tuned in.
Manual presetting
1Press [PROGRAM] then press [g, REW/3 ] or [f, 4/FF] to tune to the desired station.
SHIFT
Radio
H.BASS
2Press [PROGRAM] then press [g, REW/3 ] or [f, 4/FF] to select a channel.
3Press [PROGRAM].
The station occupying a channel is erased if another station is preset in that channel.
Manual tuning
1Press [TUNER, BAND] to select band.
The unit comes on.
Every time you press the button:
FM AM
2Press [PLAY MODE] on the remote control to select “MANUAL”.
Every time you press the button:
MANUAL PRESET
3Hold down [g/REW/3] or [f/FF/4] for a moment to search for a station.
The frequency stops when it finds a clear station.
To stop during the process, press [g/REW/3] or [f/FF/4].
Under excessive interference, a station may not be found.
Press [g/REW/3] or [f/FF/4] repeatedly to tune
“TUNED” is displayed when a radio station is tuned.
“ST” is displayed when a stereo FM broadcast is being received.
If noise is excessive in FM
Remote control only
Hold down [PLAY MODE] to display “MONO”.
Monaural sound is selected and noise reduces when reception is weak.
Hold down [PLAY MODE] again to cancel the mode. “MONO” is also cancelled if the frequency is changed.
To receive FM broadcasts allocated in 0.1 MHz steps
Main unit only
Hold down [TUNER, BAND]. The display changes in a few seconds to show the current minimum FM frequency. Continue to hold down the button until the minimum frequency changes. The step is changed.
Repeat the above to change the step back.
Note
•After changing the “allocation” setting, the frequencies you previously preset in the memory will be cleared.
•Sound is momentarily interrupted if you load/unload tapes while listening to an AM broadcast.
Preset tuning
Remote control only
There are two methods of
Automatic presetting | : All the stations the tuner can receive are preset. |
Manual presetting | : You can select the stations to preset and the |
| order they are preset in. |
Up to 15 stations each can be set in the FM and AM bands.
Preparation:
Press [TUNER, BAND] to select “FM” or “AM”.
10
Selecting channels
Press the numbered buttons to select the channel.
To enter a
AK330 | AK230 |
OR
1Press [PLAY MODE] to select “PRESET”.
2Press [g, REW/3] or [f, 4/FF] to select the channel.
Optional antenna connections
Use outdoor antenna if radio reception is poor.
FM outdoor antenna |
|
| ||
|
| FM outdoor antenna | ||
|
| (not included) | ||
|
| 75 Ω coaxial cable (not included) | ||
Rear |
| 1 |
| |
panel |
|
| 30 mm | |
of this |
| 2 | (1 3/16”) | |
1 | Shield braid | |||
unit |
| |||
|
| |||
|
| 15 mm | ||
| 2 | (19/32”) | Core wire | |
|
| 3 |
| |
•Disconnect the FM indoor antenna.
•The antenna should be installed by a competent technician.
AM outdoor antenna
AM outdoor antenna (not included)
| 5 | |
| (16 | – 40 ft.) |
Rear | 1 | AM loop |
| ||
panel |
| antenna |
of this | 2 | (included) |
unit |
| |
|
|
Run a piece of vinyl wire horizontally across a window or other convenient location.
Leave the loop antenna connected.
Note
Disconnect the outdoor antenna when the unit is not in use. Do not use the outdoor antenna during an electrical storm.
RQT7790