Before YOU Begin, Electrical Requirements

Installation Instructions

Air Conditioner

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•IMPORTANT — Save these

instructions for local inspector’s use.

•IMPORTANT — Observe all governing codes and ordinances.

•Note to Installer – Be sure to leave these instructions with the Consumer.

•Note to Consumer – Keep these instructions for future reference.

•Skill level – Installation of this appliance requires basic mechanical skills.

•Completion time – Approximately 1 hour

•We recommend that two people install this product.

•Proper installation is the responsibility of the installer.

•Product failure due to improper installation is not covered under the Warranty.

ELECTRICAL REQUIREMENTS

Some models require a 115/120-volt a.c., 60 Hz grounded outlet protected with a

15-amp time delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the possibility of electric shock hazard. If the wall outlet you plan to use is only a 2-prong outlet, it is your responsibility to have it replaced with a properly grounded 3-prong wall outlet.

Some models require 230/208-volt a.c., protected with a time delay fuse or circuit breaker. These models should be installed on their own single branch circuit for best performance and to prevent overloading house or apartment wiring circuits, which could cause a possible fire hazard from overheating wires.

CAUTION:

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

Do not change the plug on the power cord of this air conditioner.

Aluminum house wiring may present special problems—consult a qualified electrician.

TOOLS YOU WILL NEED
Phillips head screwdriver
Flat-blade screwdriver
Pencil	Ruler or tape measure
Level	Scissors or knife

Power cord includes a current interrupter device. A test and reset button is provided on the plug case. The device should be tested on a periodic basis by first pressing the TEST button and then the RESET button. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician.

AER05 specifications

The GE AER05 is a state-of-the-art aircraft engine developed by General Electric Aviation, known for its innovative design and cutting-edge technology. This engine is primarily used in regional jets and some narrow-body aircraft, making it a key player in the aviation industry.

One of the main features of the AER05 is its fuel efficiency. The engine employs advanced materials and aerodynamic designs that minimize drag and enhance overall performance. This efficiency not only reduces operational costs for airlines but also contributes to lower emissions, aligning with global efforts to promote sustainability in aviation.

Another key characteristic of the GE AER05 is its lightweight construction. The engine utilizes composite materials, allowing it to achieve a significant reduction in weight without compromising on strength or durability. This lightweight design contributes to improved aircraft performance, enabling quicker ascents and greater payload capacity.

The AER05 also incorporates advanced noise reduction technologies. It features a unique fan design that helps to minimize noise during both takeoff and landing phases. This is increasingly important as airports around the world implement stricter noise regulations. The quieter operation enhances the passenger experience and reduces the environmental impact of air travel.

In terms of maintenance, the GE AER05 is designed with the operator in mind. Its modular architecture allows for easier access to components, streamlining maintenance procedures and reducing downtime. Airlines benefit from lower maintenance costs and enhanced reliability, which is crucial for keeping aircraft in the air and minimizing delays.

The engine is equipped with sophisticated digital controls and monitoring systems. These technologies enable real-time performance analysis, allowing for proactive maintenance and operational adjustments. The data gathered can also help airlines optimize their flight operations, leading to further improvements in efficiency and cost savings.

In summary, the GE AER05 is a prominent engine in modern aviation, characterized by its fuel efficiency, lightweight design, noise reduction capabilities, maintenance-friendly architecture, and advanced digital technology. Its innovative features ensure that it meets the demands of both airlines and passengers, making it a vital asset for the future of air travel. As the aviation industry continues to evolve, the AER05 stands at the forefront, embodying the technological advancements needed to create more sustainable and efficient air transportation solutions.