GTR Smart ButtonTM, Programming, Introduction

OPEN /

Universal Garage Door Receiver Model GTR

1. INTRODUCTION

Congratulations on your purchase of the Skylink® Smart ButtonTM. The Smart ButtonTM is designed to work with Skylink® remote G6M, G6K, G6V and more. Simply replace the traditional wall button by the Smart ButtonTM, that’s all for the installation. In this kit, you will find the following:

	2 Wire
	Connectors
Smart ButtonTM	Mounting
	Accessories

	2. INSTALLATION
	Unplug the power cord of your garage door opener
WARNING	before installation to ensure power is not connected.
WARNING

GTR Smart ButtonTM

The GTR Smart ButtonTM replaces most garage door “push buttons” or “wall consoles”. There are 2 different kinds of “push buttons”.

1) Single button

2) Multi-Function Wall Console

1) Single button

If your garage door opener comes equipped with a single button “push button”, you can replace the existing push button with Skylink® Smart ButtonTM GTR. Please follow the procedures below.

2. INSTALLATION (CONT)

If you have the multi-function wall console, do not replace the wall console by the Smart ButtonTM. You need to install the Smart ButtonTM in parallel with your existing wall console.

1. Remove the existing wall console from the wall by removing the screws.

2. Remove the 2 screws that secure the wires on the wall console.

3. Connect the wires from the Smart ButtonTM to the existing wall console. Polarity does not matter, so simply pick one wire from the Smart ButtonTM, and connect it to one of the terminals on the existing wall console. Do the same for the 2nd wire.

4. After connecting the wires, mount the Smart ButtonTM on to the wall with 2 screws. Also mount the original wall console on to the wall.

5. Plug in the AC cord of the garage door opener. The red light on the Smart ButtonTM should flash 15 seconds after plugging in the power. The red light will not flash immediately after plugging in

the power, which is normal. The Smart ButtonTM is now ready to be operated.

6. If the Smart ButtonTM red light does not flash at all 2 minutes after plugging in the AC cord, your garage door opener is probably too old.

However, the Smart ButtonTM will still work by plugging in an adapter (purchase separately). Please contact Skylink® to purchase the adapter.

Rating of the transformer: 12V DC, 100mA

Diameter of DC plug : 3.5mm

Note: Straighten up the antenna to improve signal reception.

1.Remove the existing push button by removing the screws.

2. Disconnect the 2 wires that are connected to the existing push button.

3. Connect the 2 wires from the existing wall button to the GTR Smart ButtonTM. Twist the 2 wires together with the wire connector

provided. Polarity does not matter, so simply pick one wire from the existing wall button, and

connect it to one of the wires on the Smart

ButtonTM. Do the same for the 2nd wire. 4. After connecting the wires, mount the Smart

ButtonTM on to the wall with 2 screws.

5. Plug in the AC cord of the garage door opener. The red light on the Smart ButtonTM should flash 15 seconds after plugging in the power. The

red light will not flash immediately after plugging in the power, which is normal. The

Smart ButtonTM is now ready to be operated.

Remove existing wires

Antenna

3. OPERATION

If the red light on the Smart ButtonTM is flashing slowly, that indicates it is in standby mode. When a valid remote control signal is received, it will open / close the garage door.

Simply press the button on the remote control or Smart ButtonTM, it will open / close the garage door.

Programming

Learn additional remote controls

Smart ButtonTM can learn up to 15 remote controls. To learn additional remote controls, follow the instructions below:

1.Press the learn button on the side of the GTR.

2.Once the learn button is pressed, the LED will flash quickly. You may release the learn button.

Note: Straighten up the antenna to improve signal reception.

2) Multi-Function Wall Console

Multi-Function Wall Console normally comes with 3 buttons that can be used to:

1) operate the garage door opener lighting, 2) lock the receiver so it doesn’t accept remote control operation, and

3) push button for door opening / closing

3. Press the button on the remote control you would like to program.

4. Once the remote control is programmed, the LED will flash slowly, in the same way as it flashes in standby mode.

Learn Button

5. You may now operate the garage door opener with this new remote control.

GTR specifications

SkyLink GTR represents a remarkable leap in the evolution of advanced transport technology, masterfully blending speed, efficiency, and cutting-edge design. This next-generation vehicle is poised to redefine the commuting experience for enthusiasts and everyday users alike, featuring a myriad of unique characteristics and technologies.

At the heart of the SkyLink GTR is a powerful electric drivetrain that delivers rapid acceleration and impressive top speeds. This powerful system is complemented by a lightweight body structure, composed of advanced composite materials designed to enhance aerodynamic efficiency and reduce drag. As a result, the GTR boasts a remarkable power-to-weight ratio, contributing to its agility and performance on various terrains.

The GTR incorporates an innovative regenerative braking system, which captures energy during braking and redistributes it to power the vehicle. This not only increases energy efficiency but also extends the overall range of the vehicle, allowing users to travel further on a single charge. Additionally, the long-range battery pack can be charged quickly, thanks to cutting-edge fast-charging technology, making it convenient for daily use.

Equipped with state-of-the-art artificial intelligence systems, the SkyLink GTR offers autonomous driving capabilities. Sensors and cameras integrated throughout the vehicle continuously monitor the surrounding environment, allowing for real-time adjustments to driving patterns and navigation routes. This ensures a safe and smooth driving experience, granting users the luxury of hands-free travel when desired.

In terms of connectivity, the GTR boasts advanced telematics systems that provide a seamless link between the vehicle, its driver, and their mobile devices. This integration allows users to not only control various vehicle settings but also access a range of applications for enhanced navigation, entertainment, and performance tracking.

The interior of the SkyLink GTR reflects a commitment to driver and passenger comfort, featuring premium materials and customizable settings for an optimal experience. An innovative heads-up display provides essential data in the driver’s line of sight, ensuring that important information is always readily available without distraction.

In summary, the SkyLink GTR is a pioneering vehicle that combines powerful performance, sustainable technology, and luxurious design. With its emphasis on efficiency, safety, and connectivity, it stands as a testament to the future of transportation, offering an exhilarating driving experience that appeals to both enthusiasts and everyday users.