SkyLink GBRV manual Introduction, Receiver Installation, Operation

Page 1
LED
OPEN /
CLOSE Button
LED
Learn
Button

Universal Garage Door

 

Remote Control

Model GBRV

 

 

1. INTRODUCTION

 

 

 

Congratulations on your purchase of the Skylink® GBRV Universal Garage Door Remote Control. This is a kit with a universal remote control and Smart ButtonTM. In this kit, you will find the following:

 

 

Crimper

Visor clip

Garage Door

 

Receiver

 

Remote Control

 

Smart ButtonTM

Double Sided Tape

(Battery included)

GB-318

 

2. RECEIVER INSTALLATION

 

 

 

Unplug the power cord of your garage door opener before installation to ensure

 

power is not connected.

WARNING

DO NOT let children use the gargae door Transmitter without adult supervisor.

Children can injure themselves or others by the garage door.

DO NOT use remote to control the door without safety beams.

2.RECEIVER INSTALLATION (CONT)

5.If the wall button wires are hidden inside the wall, please connect the “Easy ClipTM” to the exposed wires attached to the

terminals of the garage door opener.

6.Power up the garage door opener, the red LED on the Smart ButtonTM GB-318 should keep flashing slowly within 2 minutes.

Antenna

If the Smart ButtonTM GB-318’s red LED does not flash after the Smart ButtonTM GB-318 has been connected to the wall button’s wires for 2 minutes, your garage door opener is probably too old. However, the Smart ButtonTM GB-318 will still work if you plug in an adapter (purchased separately). Please

1. Open up the “Easy ClipTM” and place it underneath the existing 2 wires of the wall button / wall console.

2. Ensure a pair of the wall button ribbon wires are placed properly inside the channels of the “Easy ClipTM”.

Wall Button

Ribbon Wires

NOTE:

Ensure the ribbon wires are not twisted but laid flat inside the clip.

Easy ClipTM

contact Skylink® to purchase the adapter.

Rating of the transformer: 12V DC, 100mA Diameter of DC plug : 3.5mm

7. Secure the Smart ButtonTM GB-318 properly with the mounting accessories.

Note: Do not cut the antenna! Straighten up the antenna to improve signal reception.

Note: After installation of the “Easy Clip TM ”, if you want to re-install the Smart Button TM GB-318 to another place, please open the “Easy Clip TM ” by gently unlocking the two buckles with a screw driver, and remove it from the wires. Do not re-use the “Easy Clip TM ”, refer to Step 4 to re-install it.

If your wall button ribbon wires are not the same kind as shown in the diagram, please refer below (4) or visit our website www.skylinkhome.com or contact us for more information.

3.Press and lock the clip by snapping it together. The included Crimper helps you lock the “Easy ClipTM”. Close the cover and press down to lock the cover using this Crimper until you hear a “click”.

Press / lock

Ribbon Wires

3. PROGRAM TRANSMITTER G6V TO RECEIVER GB-318

You need to do the programming in order to add the transmitter to a receiver. Smart ButtonTM GB-318 can learn up to 10 remote controls.

To add remote controls, follow the instructions below:

1.Press the learn button on the side of the Smart ButtonTM GB-318.

2.Once the learn button is pressed, the LED will flash quickly. Release the learn button.

3.Within 30 seconds, press the button on the transmitter

that you want to program to the receiver.

4. Once the remote control is programmed, the LED will flash slowly, in the same way as it flashes in standby mode.

5. You may now operate the garage door opener with this new remote control.

4.If the “Easy ClipTM” cannot clip with the wires from your wall button, cut off the “Easy ClipTM” then connect two wires from the Smart ButtonTM GB-318 to the wall button.

a) Disconnect the existing wall button from the wall.

b) Connect the 2 wires from the Smart ButtonTM GB-318 to your existing wall button. Polarity does not matter, so simply pick one wire from the Smart ButtonTM GB-318 and connect it to one of the screw terminals on your wall button. Connect the 2nd wire to the other screw terminal.

c) Reconnect the wall button back.

Smart ButtonTM GB-318

4. OPERATION

If the red LED flashes slowly, the Smart ButtonTM GB-318 is in standby mode. When a valid remote control signal is received, it will open / close the garage door.

Press the programmed button on the remote control or Smart ButtonTM GB-318, it will open / close the garage door.

Note: After connecting this NEW Remote Control to your wall button, your existing remote control will still work with this connection.

Image 1
Contents Introduction Receiver InstallationProgram Transmitter G6V to Receiver GB-318 OperationBattery Trouble ShootingVisor Clip Installation Warranty
Related manuals
Manual 2 pages 63.14 Kb

GBRV specifications

SkyLink GBRV is an innovative vehicle that represents the pinnacle of modern engineering and technological integration in the realm of personal and commercial transportation. This next-generation vehicle stands for "Ground-Breaking Recreation Vehicle," and it combines unparalleled versatility, cutting-edge features, and sustainable technologies.

One of the standout characteristics of the SkyLink GBRV is its hybrid powertrain. It seamlessly blends traditional fuel sources with electric power, ensuring optimal efficiency while minimizing emissions. This dual-engine system allows the vehicle to switch between modes, enabling it to travel longer distances without sacrificing performance. The electric component provides instant torque, making the GBRV exceptionally responsive and capable of handling various terrains, from urban environments to off-road adventures.

The interior of the SkyLink GBRV is designed with user comfort and convenience at the forefront. Equipped with an intelligent infotainment system, passengers can access navigation, entertainment, and vehicle diagnostics with ease. The system is powered by artificial intelligence, providing personalized recommendations based on user preferences. Additionally, the spacious cabin incorporates modular seating arrangements, allowing users to reconfigure the space as needed for leisure or cargo requirements.

Safety is a significant focus in the design of the GBRV, featuring a robust suite of advanced driver-assistance systems (ADAS). These include adaptive cruise control, lane-keeping assist, and collision detection Systems designed to enhance the driving experience while ensuring passenger safety. The integration of a 360-degree camera system offers full coverage around the vehicle, making parking and maneuvering in tight spaces a breeze.

Moreover, the SkyLink GBRV is built with sustainability in mind. The materials used in its construction are eco-friendly and recyclable, reducing the vehicle's overall carbon footprint. The incorporation of solar panels on the roof contributes to energy efficiency, allowing the vehicle to harness renewable energy as it travels.

In summary, the SkyLink GBRV is more than just a vehicle; it’s a forward-thinking solution that harmonizes technology, comfort, safety, and sustainability. With its hybrid powertrain, intelligent infotainment system, advanced safety features, and eco-friendly materials, the GBRV is poised to set a new standard in the realm of recreational vehicles and beyond. Whether for everyday commuting or adventurous excursions, the SkyLink GBRV offers a transformative experience that adapts to the needs of its users while prioritizing the health of our planet.