SkyLink SK7 Programming, Erasing, Enable/Disable On/O or Dimming, Flashing Alert Mode

Page 2

Section 4 - Programming

NOTE: Before programming, remove the wall plate on the Wireless Wall Switch transmitter by loosening the screws.

NOTE: Use a sharp non-conductive object, like a pen or pencil, to press the learn button.

1.Touch the metal touch plate on the Wall Switch receiver to turn the lights on. The two blue LEDs should go o￿.

2.Press and hold the learn button for about three seconds until the upper blue LED ￿ashes quickly and then release the learn button.

Blue LEDs

Touch Plate

 

Learn Button

3.

Press the learn button on your Wireless Wall Switch transmitter. The red

 

LED will be on for 15 seconds.

4.

Press the pad (switch) on the Wall Switch Transmitter, the red LED will

 

￿ash and then go o￿. The upper blue LED on the Wall Switch Receiver will

 

also turn o￿.

Section 5 - Erasing

NOTE: All previously programmed devices will be erased. You must re-program the devices you want to keep.

NOTE: Use a sharp non-conductive object, like a pen or pencil, to press the learn button.

1.Power o￿ the Wall Switch receiver by sliding the air gap switch into the o￿ position.

2.Press and hold the learn button and slide the air gap switch back into the on position.

Air Gap Switch

Blue LEDs

Learn Button

Section 6 - Enable/Disable On/O￿ or Dimming

NOTE: On/O￿ Mode turns the light on/o￿, without dimming and Dimming Mode turns the light on/o￿ or dims/brightens.

WARNING: Non-dimmable load has to always be working under the On/O￿ Mode. Using non-dimmable load under Dimming Mode may damage the non-dimmable CFL.

NOTE: The factory default operating mode is on/o￿.

1.Turn the light on with the programmed transmitter or touch pad.

2.Press and hold the button on the transmitter that is programmed to the Wall Switch receiver for 10 seconds or touch the pad with your ￿nger for 10 seconds. The LED will ￿ash quickly.

3.The light in the room will ￿ash. If it ￿ashes once, it is in On/O￿ Mode. If it ￿ashes twice, it is in Dimming Mode.

4.Repeating step 2 will toggle the settings between On/O￿ Mode and Dimming Mode.

Section 7 - Flashing Alert Mode

NOTE: If the Flashing Alert Mode is activated, the light connected to the Wall Switch receiver will ￿ash for a predetermined time interval and then turn o￿.

NOTE: You must compete the programming sequence within the 15-second interval, otherwise the Wall Switch receiver will quit from programming mode and you will need to start again from step 1.

NOTE: Use a sharp non-conductive object, like a pen or pencil, to press the learn button.

1.To program a transmitter to operate in Flashing Alert Mode, hold the learn button on your Wall Switch receiver for about 10 seconds, until the upper blue LED ￿ashes slowly, then release the learn button.

2.Press the learn button on your transmitter.

3.Once the transmitter is programmed, both blue LEDs will ￿ash quickly and stop ￿ashing.

4.The transmitter has been successfully programmed.

Section 8 - Countdown Timer Mode

NOTE: If the Countdown Timer Mode is activated, the light connected to the Wall Switch receiver will be on for the predetermined time interval and then turn o￿.

NOTE: You must compete the programming sequence within the 15-second interval, otherwise the Wall Switch receiver will quit from programming mode and you will need to start again from step 1.

NOTE: Use a sharp non-conductive object, like a pen or pencil, to press the learn button.

1.To program a transmitter to operate in Countdown Timer Mode, hold the learn button on your Wall Switch receiver for about 20 seconds, until the upper blue LED is on steadily, then release the learn button.

2.Press the learn button on your transmitter.

3.Once the transmitter is programmed, both blue LEDs will ￿ash quickly and stop ￿ashing.

4.The transmitter has been successfully programmed.

5. Both wall switches are now programmed.

CR 2032

Learn Button

+

 

Red

 

LED

Pad

 

3.The blue LEDs will ￿rst turn on and then turn o￿.

4.Release the learn button.

5.All devices have now been successfully erased.

Blue LEDs

Blue LEDs

Learn Button

Learn Button

NOTE: Once you have successfully completed the programming, go to section 9 to setup the timer duration for the transmitter.

NOTE: Once you have successfully completed the programming, go to section 9 to setup the timer duration for the transmitter.

Section 9 - Setting a Timer Duration

NOTE: This section is for transmitters that are programmed to Flashing Alert Mode and Countdown Timer Mode. The timer duration for both modes can be set for the following times: 1 minute, 5 minutes, 15 minutes, 30 minutes or 60 minutes.

NOTE: Once the number of ￿ashes reaches 5, it will stay at this setting. If you would like to go back to other settings, such as 1 minute, release the button and repeat from step 1 to start over.

NOTE: Use a sharp non-conductive object, like a pen or pencil, to press the learn button.

1.The connected light must be turned o￿ and the two blue LEDs should be on.

2.Press and hold the learn button for three seconds until the lower blue LED ￿ashes once. The number of ￿ashes indicates the timer duration.

Number of Flashes

Timer Duration

 

 

1

1 min.

 

 

2

5 min.

 

 

3

15 min.

 

 

4

30 min.

 

 

5

60 min.

 

 

3.Continue to hold the learn button until it reaches the desired setting. The status will change every 6 seconds; so holding the learn button for another 6 seconds the number of ￿ashes will change from 1 to 2, 2 to 3 etc.

Once a transmitter is programmed for the timer mode, activating this programmed transmitter will turn the lights on for the speci￿ed timer duration. To stop timer countdown, press a programmed button for regular mode.

NOTE: During a timer countdown if the Wall Switch receiver receives another signal for timer operation, the timer will start again and override the previous timer. This will extend the on period by another timer interval.

Section 10 - Replacing the Battery

1.Remove the wall plate from the Wireless Wall Switch transmitter by loosening the two screws.

2.Remove the existing battery by sliding it out.

3.Insert the new battery, positive side up, by sliding it in and pushing down on the battery to lock it in place.

4.When the battery is installed, the red LED on the transmitter will be on for one second.

 

Push

 

Slide in

Down

 

2

20

32

+

+

 

 

Battery

CR 2032

(Positive side up)

+

Red

LED

Troubleshooting

Problem

Solution

 

 

Wall Switch Receiver`s

- Ensure the corresponding wires are

connected correctly. Refer to Section 1.

LEDs and the connected

- Ensure the wires are side by side and

load will not turn on.

held together when pushing them

 

 

inside the wire nuts.

 

 

- Check that the circuit breaker is turned

 

on.

 

 

 

- If there are white wires (neutral) in the

My switch has more than

3 wires in the wall box.

wall box, connect the white wire with a

 

wire nut. Only connect the Load and

 

Live wires from the wall box to the Wall

 

Switch Receiver.

 

 

The Wall Switch Receiver

- This is normal. Ensure the connected

 

is getting warm to touch.

load does not exceed the maximum

 

rating.

 

 

The range of my Wall

- Keep the antenna wire as straight as

Switch Receiver is

possible and put it directly into the dry

decreasing.

wall or via the hole in the wall box.

 

 

It takes a long time for

- Ensure the timer duration is set to the

the light to turn o￿ when

desired setting.

set to Timer Mode.

- Check that there were no other Timer

 

Mode signals being received as that will

 

extend the ON period by another

 

interval.

 

 

Can I connect the Wall

- No. Purchase the Skylink Wall Switch

Switch Receiver with

Receiver (WE-001/WE-318) instead of

600W lights?

this Wall Switch Receiver.

 

 

Can I dim the CFL with

- Ensure the CFL is dimmable.

the Wall Switch Receiver?

 

 

 

Optional Snap-On Decorative Cover

Snap a cover into your Skylink Wall Switch!

Place the Snap-On Cover on the opening of the Wall Switch receiver for a more stylish look. Press or tap the cover, TM-001, to turn lights on/off or dim/brighten. Or carry the Snap-On Remote,TM-318, with you for local control and when you are done snap it back onto the Wall Switch.

Snap-On Cover

Snap-On Remote

Model: TM-001

Model: TM-318

For more information visit www.skylinkhome.com

Accessories

Add up to eight Skylink Wireless Transmitters!

Wireless Wall Switch

Motion Sensor

Model: TB-318

Model: ID-318

Snap-On Remote

Keychain Remote

LCD Deluxe Remote

Model: TM-318

Model: LK-318

Model: TD-318

Wireless Remote Control TC-Series

TC-Series Remotes are available in 1 to 14 buttons.

For more information visit www.skylinkhome.com

Page 1 Page 2
Image 2
Page 1 Page 2
Contents ONE Year Warranty Wireless 3 WAY ON/OFF/DIMMER KITInstalling with Double Sided Tape Installing with ScrewsCountdown Timer Mode Enable/Disable On/O or DimmingFlashing Alert Mode Setting a Timer Duration

SK7 specifications

SkyLink SK7 is a cutting-edge satellite communication system designed to provide seamless connectivity for a variety of applications, ranging from government to commercial uses. With a focus on reliability, speed, and coverage, the SK7 is a game-changer in the satellite communication landscape.

One of the standout features of the SkyLink SK7 is its advanced phased array antenna technology. This innovative design allows for faster signal acquisition and tracking, enabling users to maintain a stable connection even in challenging environments. This is particularly beneficial for mobile applications, such as maritime and aviation sectors, where connectivity can often be intermittent.

Another significant characteristic of the SK7 is its high throughput capability. The system supports multi-gigabit data rates, making it suitable for bandwidth-intensive applications, such as high-definition video streaming and large data transfers. This ensures that organizations can rely on the SK7 for their critical communication needs, without compromising on speed or efficiency.

The SkyLink SK7 also incorporates powerful encryption protocols, ensuring that data transmitted over the network is secure and protected from unauthorized access. This is especially crucial in industries where sensitive data is transmitted, such as defense and finance. The system is designed to meet stringent compliance standards, giving users peace of mind when it comes to data security.

In terms of user experience, the SK7 offers an intuitive interface for easy operation and management. Users can monitor their connection status, manage bandwidth, and troubleshoot issues quickly and efficiently. This user-friendly approach reduces the need for extensive training and allows for smoother implementation across various organizations.

Moreover, the SK7 is built to be highly resilient, with robust hardware capable of withstanding harsh environmental conditions. This durability makes it an ideal choice for remote locations and extreme weather scenarios, ensuring constant connectivity when users need it the most.

Additionally, the SkyLink SK7 is compatible with various satellite constellations, allowing for flexible deployment options. Users can choose between different service providers and configurations, tailoring the system to their specific needs and objectives.

In conclusion, the SkyLink SK7 is a state-of-the-art satellite communication system that combines advanced technologies with robust features to deliver exceptional performance. Its high throughput, security measures, user-friendly interface, and resilience make it an ideal solution for organizations requiring reliable connectivity in an increasingly connected world.
Top Page Image Contents