SkyLink HA-434TL manual Joint, Erasing a sensor, High 2-Low, Walk Test

lndoor/Outdoor

Motion Sensor ModelHA-434TL

The lndoor/Outdoor Motion Sensor is designed to monitor movement around your house. The motion sensor can be placed either indoor or outdoor. Once motion is detected, the receiver will respond with flashing along with alert beeping or alarm.

ln this package, you should find an lndoor/Outdoor Motion Sensor, ball- head joint, screws.

ru	r	joint	2pcs 3xlSscrews
			(tnctuded)
lndoor/Outdoor
Motion Sensor

MOUNTING

A ball-head joint is necessary to mount the sensor at a desire location. A height of 7 tl is recommended, depending on your application. Once a location is selected, mount the ball-head joint to this location by screws provided. Once the ball-head joint is mounted to the wall, slide the back of the sensor into the ball-head joint. The mounting angle can be adjusted. Please refer to "Walk Test" to determine the best mounting

angle.

-)

Please follow the instructions below to setup your motion sensor.

The sensor must be programmed to the Household Alert" Long Range Receiver before they can communication. You may program the sensor to one of the 4 zones. Follow the instructions below:

1.Plug in an AC adapter to the receiver.

2.The green LED will be on indicating it is turned on.

3.Open the back cover and there is a learn button. Press and hold this learn button for 5 seconds, until both green LED and zone 1 red LED flash. You may now release the learn button.

4.lf you would like to program the sensor to zone 1, activate the sensor while the zone 1 red LED is flashing. Press the SET button on the back of the sensor to activate it.

5.lf you would like to program the sensor to other zones, press the learn button again, until the red LED flashes at the zone you want to program the sensor to, then activate the sensor.

6.Once the sensor is programmed, the green LED will be steadily on and none of the red zone LEDs will be on.

SET Button

I

Plug in the adapter to the receiver

WALK TEST
After mounting the sensor at the desired location, it is	I
important to perform a walk test in order to determine	]'u
if the sensor is detecting the things you want to detect.
	Il

ln order to control how far the sensor can "see", this can be done by adjusting the angle of the sensor. To reduce the detection range, simply move the sensor downward. To increase the range, move the sensor up to around 12 degrees. This will give the maximum range. However,

this may not be desired if the sensor is placed outdoors, since a false trigger may occur if the sensor is set to detect motion in a distance.

You should walk in the area that you would like the sensor to monitor. Place the slide switch on the side of the receiver to "Alert" position. The receiver will beep if the sensor detects your movement. lf the receiver does not respond, adjust the mounting angle accordingly. After motion is detected once, the sensor will not be triggered unless no motion is detected tor 20 seconds. Therefore, wait for at least 20 seconds during walk testing between 2 activations.

Perform walk test in the undesired area to ensure movement cannot be

detected.

Tips: The sensor should not face towards direct sunlight, placing near heat or cold producing devices (i.e. NC or furnance vents, fans, ovens, heaters etc.) that may cause false triggers

Learn Button lnsert 9V alkaline battery (option) to the sensor

Note: Each zone can program up to 4 sensors. lf you try to program a fifth sensor into a zone, the first programmed sensor will be erased.

Erasing a sensor

You cannot erase a specific sensor. You must erase all sensors from the receiver, then program the ones you would like to keep. To erase all the sensors from the receiver:

1.Remove the adapter from the receiver.

2.Open the back cover, press and hold the learn button. Do not release the learn button until step 4.

3.while holding onto the learn button, plug in the adapter to the receiver.

4.You may release the learn button when the LEDs on the receiver are on.

5.You have erased all sensors from the receiver.

Move the sensor downward to	Move the sensor up to around
reduce the range.	l2etogive maximum range.

SENSOR SENSITIVITY

The sensitivity of the motion sensor is adjustable. change the setting by placing the connector on either the "High" (connector position "1") or "Low" (connector position "2") position. When the sensitivity is set to "Low", more movement is required to trigger the sensor. lt is recom- mended to set the sensitivity to "Low" and perform a "Walk Test". lf the walk test result is satisfied, the sensitivity does not require to be adjusted further. lf the walk test

result shows the sensitivity is too low, then you can change the

sensitivity setting to "High". Please perform the walk test after changing the sensitivity setting.

1-High 2-Low