i. Tech Dynamic i.Cube Getting Started, Charging Your Headset cont’d, Using Your Headset

Getting Started

Before using your i.Cube (“headset”) for the first time, please ensure that

1.the headset is fully charged;

2.the fully charged headset must be paired and connected with a Bluetooth mobile phone.

Charging Your Headset

The headset comes with a built-in rechargeable battery. Prior to using the headset for the first time, you are recommended to fully charge the battery.

Charging Socket

fig.2

Use only the supplied charger to charge the headset.

5

Charging Your Headset (cont’d)

Status	Status Indicator	Audio
• Charging	• Red light
• Fully charged	• Blue light
• Low battery	• Flashing red light	• a short beep every 1 minute
• Out of battery	• The light goes off

♦3 hours are required to fully charge the headset.

♦Charging indication will be delayed for a few seconds if the headset has not been used for a long time or the battery is drained.

Pairing Your Headset with a Bluetooth Mobile Phone

1)Ensure the headset is off.

2)To activate the pairing mode, press and hold the headset’s MFB for 8 seconds without releasing your finger until its status indicator flashes alternating blue and red lights.

3)Activate your mobile phone’s Bluetooth, search Bluetooth devices, select “i.Cube” and enter the passcode “0000”. When the pairing is completed, the headset’s status indicator will flash a blue light rapidly five times.

If the pairing cannot be completed within three minutes after the pairing mode has been activated, the headset’s status indicator will flash purple rapidly five times and then turns off. Repeat steps 1 to 3 to pair both devices again.

6

Pairing Your Headset with Two Mobile Phones (Multipoint)

i.Cube supports a Multipoint function to allow simultaneous pairing of the headset with two mobile phones.

1.Follow the pairing procedure as instructed in “Pairing Your Headset with a Bluetooth Mobile Phone” to pair the headset with the first mobile phone.

2.Repeat the pairing procedure for the second mobile phone.

3.On the first mobile phone’s menu, activate its Bluetooth connection with the headset.

Using Your Headset

Function	Button	Audio	Status Indicator
Power ON	Press and hold the MFB for 2	a short beep	Flashing blue light
	seconds

When you turn on your headset for the first time, the headset automatically enters the pairing mode, i.e. the status indicator flashes alternating blue and red lights. This allows you to immediately pair your headset and mobile phone.

If your headset is paired with your mobile phone, press the MFB once more after you turned on the headset to re-connect the mobile phone and the headset.

Power OFF	Press and hold the MFB for 2	a long beep Red light for two seconds
	seconds	and then the light goes off
If you do not plan to use the headset for a while, you are recommended to turn off
the Bluetooth function of your mobile phone.		7

Using Your Headset (cont'd)

Function	Button	Audio	Status Indicator
Answer a Call	Press the MFB once		Flashing blue light
Answer a Second Call	Press the MFB once to terminate	a beep	Flashing purple light
intended for your other	the first call, then press the MFB		when there is a second
mobile phone	once again to answer the second		call intended for your
	call		other mobile phone
End a Call	Press the MFB once		Flashing blue light
Adjust Volume	Press the Vol＋/－once to	a short beep	Flashing blue light
	increase / decrease by 1 level
Mute a Call	Press either volume key for 2	2 beeps every	Flashing blue light
	seconds	5 seconds
Cancel Call Muting	Press either volume key for 2	2 short beeps	Flashing blue light
	seconds
Voice Dialing	Press the MFB once	a short beep	Flashing blue light

Say the voice tag as soon as you hear the short beep and you must have recorded the voice tag into your mobile phone.

Last No. Redial Double click the MFB Flashing blue light

8