13
LIFT ARM
FIRST
IMPORTANT: Always clear sand and rust from system.
•Make sure water supply is off. Remove valve TOP by lifting arm and rotating top and arm 1/8 turn counterclockwise, pressing down slightly on cap.
•While holding a container over the uncapped VALVE to prevent splashing, turn water supply on and off a few times. Leave water supply off.
•Replace TOP by engaging lugs and rotating 1/8 turn clockwise. MAKE CERTAIN TIP IS TURNED TO THE LOCKED POSITION. VALVE MAY NOT TURN ON IF TOP IS NOT FULLY TURNED TO THE LOCKED POSITION.
TROUBLESHOOTING
IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 13.
IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because:
•The end of the refill tube is inserted into overflow pipe, below water level in tank. Attach refill tube to overflow pipe using "S" clip provided.
•The flush valve is leaking because it's worn, dirty or
misaligned with tank ball or flapper (replace with a new flapper).
IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time, Fluidmaster Model 242 Replacement Seal may be needed.
Go to our website at www.fluidmaster.com for more solutions to toilet problems.
For troubleshooting information please contact:
30800 Rancho Viejo Road
San Juan Capistrano, CA 92675
TROUBLESHOOTING GUIDE
PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
Does not flush | a. Water supply valve closed. | a. Open valve and allow water to fill tank. |
| b. Supply line blocked. | b. Shut off water supply, disconnect supply line and inspect all gaskets and |
| | washers. Reassemble. Also, see Fluidmaster maintenance. (see Step 13) |
| c. Flush valve chain too loose or disconnected. | c. Readjust chain length as required. |
| d. Sand or debris lodged in water control. | d. Shut off water supply. Remove cap and clean as per Step 13. |
| | |
Poor or sluggish flush | a. Bowl water level too low. | a. Check that refill tube is connected to water control and inserted into tank |
| | overflow without being kinked or damaged. |
| b. Supply valve partly closed. | b. Open supply valve fully. Be sure that proper supply tube size is used. |
| c. Partially clogged trapway and/or drain pipe and/or vent. | c. Remove obstruction. Consult a plumber if necessary. |
| d. Supply pressure too low. | d. Normal supply pressure must be at least 20 psi. |
| | |
Toilet leaks | a. Poor supply line connection. | a. Review Step 9 of installation procedure. |
| b. Poor bowl to tank/floor connection. | b. Review Step 4 through 7 of installation procedure. |
| | |
Toilet does not shut off | a. Flush valve chain too tight, holding flush valve open. | a. Readjust chain length as needed. Review Step 10. |
| b. Flush valve seat and/or flapper worn or deformed. | b. Shut off water supply. Replace flush valve. |
| c. Sand or debris lodged in water control. | c. Shut off water supply. Remove cap and clean per Step 13. |
| | |
CADET® 3 FLUSH RIGHT™ TOILET FIVE YEAR LIMITED WARRANTY
This limited warranty applies only to the original purchaser and installation of the products. In the event of a limited warranty claim, proof of purchase will be required - save sales receipt.
For this warranty to become effective, the accompanying warranty registration card and proof of purchase must be completed and returned to the address on the warranty registration card within 30 days of purchase.
If inspection of this AS America, Inc. (”American Standard”) plumbing product, inclusive of china and all mechanical components, within five years after its initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American Standard.
This warranty DOES NOT COVER any damage caused by the use of in-tank cleaners.
American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall
American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:
In the United States: | In Canada: | In Mexico: |
American Standard Brands | AS Canada ULC | Customer Service Manager |
P.O. Box 6820 | 2480 Stanfield Rd. | AS Maquila, S.A. de C.V. |
Piscataway, New Jersey 08855 | Mississauga, Ontario | Via Morelos #330 |
Attention: Director of Consumer Affairs | Canada L4Y 1S2 | Col. Santa Clara |
| Toll Free: (800) 387-0369 | Ecatepec 55540 Edo. Mexico |
For residents of the United States, warranty | www.americanstandard.com.mx |
information may also be obtained by calling | www.americanstandard.ca | |
the following toll free number: (800) 442-1902 | | |
www.americanstandard-us.com | | |
