Adjustments, Care and Cleaning | American Standard 2264.702 specs

8CAUTION: Overtightening of COUPLING NUT could result in breakage and potential flooding.

	TANK
WATER INLET
WASHER
COUPLING NUT	FLEXIBLE
COUPLING NUT	SUPPLY
	VALVE NUT
	COMPRESSION
	COLLAR

TRIM PLATE

VALVE

CONNECT WATER SUPPLY

a.Connect water supply line between shutoff valve and tank water inlet fitting. Tighten COUPLING NUT 1/4 turn beyond hand tight. Check that refill tube is inserted into overflow tube.

b.Turn on supply valve and allow tank to fill until float rises to shutoff position.

c.Check for leakage at fittings, tighten or correct as needed.

d.Do not use plumber's putty to seal these fittings.

9		FLOW RATE
TO RAISE		ADJUSTMENT
WATER			LIFT
LEVEL	+	OVERFLOW	LIFT
		OVERFLOW	ROD
TO LOWER		TUBE	ROD
		TUBE
	-	REFILL
WATER		REFILL
LEVEL		TUBE
TRIP			FLOAT	FIG. 10A
LEVER	C L		FLOAT
LEVER			BALL
			BALL
WATER CONTROL
ASSEMBLY
WATER LINE			FLUSH
LEVEL			FLUSH
LEVEL			VALVE
			VALVE
			FLOAT
WATER INLET			FLAPPER
WATER INLET			ASSEMBLY

FLUSH VALVE

ADJUSTMENTS

a.Flush tank and check that tank fills and shuts off within 30 to 60 seconds, and tank water level is set as specified on tank rear wall.

b.To adjust water level: turn water level adjustment screw counterclockwise to raise level; turn adjustment screw clockwise to lower level.

c.To adjust flow rate (tank fill time): turn flow rate adjustment screw clockwise to decrease flow rate (increase fill time); turn adjustment screw counterclockwise to increase flow rate (decrease fill time).

d.Carefully position tank cover on tank.

e.The flush valve float has been factory set and does not require adjustments. Repositioning of the float will change the amount of water used which may effect the toilet's performance.

f.If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the bead chain from the retainment clip (see Fig. 10A) and take up slack on the chain, and reinsert on lift rod. Make sure the chain is not too taught.

REPAIR PARTS LIST Repair parts are determined by toilet tank number which can be found marked inside tank.

NOTE: "XXX" represents color or trim finish options. Specify when ordering.

FOR 4094 ANTIQUITY, 4095 REPERTOIRE, AND		FOR 4074.039 HERITAGE
4094.702 WILLIAMSBURG

PART NO.	DESCRIPTION	PART NO.	DESCRIPTION
730288-XXX0A	TRIP LEVER	730283-XXX0A	TRIP LEVER
730535-XXX0A	TRIP LEVER (WILLIAMSBURG ONLY)	047227-XXX0A	BOLT CAP COVER PLATE KIT #207
034783-XXX0A	BOLT CAP KIT (INCL 2 COVERS &	738352-0070A	WATER CONTROL ASS'y W FLOAT BALL
	WASHERS)	738181-0070A	FLUSH VALVE
738462-0070A	WATER CONTROL ASS'y W FLOAT BALL	047158-0070A	COUPLING KIT, BOWL-TO-TANK
738181-0070A	FLUSH VALVE	738258 -0070A	FLAPPER ASSEMBLY
047158-0070A	COUPLING KIT, BOWL-TO-TANK
738258 -0070A	FLAPPER ASSEMBLY

11CARE AND CLEANING

When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish.

!WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage.

American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite).

- 3 -

730489-100 Rev. B

2264.702 specifications

The American Standard 2264.702 represents a remarkable fusion of design, durability, and functionality in modern bathroom fixtures. A part of the renowned American Standard product line, this model is a prominent choice for homeowners seeking a blend of innovation and style.

One of the main features of the 2264.702 is its exceptional water efficiency, adhering to WaterSense standards. This not only helps reduce water consumption but also contributes to lower utility bills, making it an environmentally friendly option. The faucet employs advanced aerator technology that generates a steady flow of water while maintaining pressure, ensuring a satisfying user experience without sacrificing performance.

In terms of design, the American Standard 2264.702 boasts a sleek and contemporary look that complements a wide array of bathroom aesthetics. Its smooth lines and minimalist form create a sophisticated yet functional centerpiece for washbasins. With attractive finishes available, including polished chrome and brushed nickel, this model can easily match existing bathroom décor.

Durability is also a key characteristic of the 2264.702. It is constructed from high-quality materials designed to withstand the rigors of everyday use. The ceramic disc cartridge ensures a leak-free operation and prolongs the faucet's longevity, while the finish is resistant to tarnishing and corrosion, maintaining its fresh appearance over time.

Installation is simplified with this model, as it comes with a robust mounting system that fits standard sink configurations. The user-friendly design extends to maintenance, with features such as removable aerators for easy cleaning and reduced mineral buildup.

The American Standard 2264.702 also emphasizes user comfort with its ergonomic handle design, which allows for smooth operation. This ensures that temperature and water flow can be adjusted effortlessly, catering to the needs of all users.

In summary, the American Standard 2264.702 is not just a faucet; it's a statement of quality and design. With its blend of innovative technology, aesthetic appeal, and durability, it stands as a prime example of what modern bathroom fixtures can achieve. For those looking to upgrade their bathrooms, the 2264.702 is a worthy consideration that promises both elegance and efficiency.