American Standard 4400 SERIES Test Installed Faucet, HOT Limit Safety Stop Adjustment

Page 3

5

TEST INSTALLED FAUCET

 

 

 

 

Move HANDLE down into "off" position and remove AERATOR.

 

 

 

 

 

 

 

 

 

 

 

 

Turn on water supplies and check connections for leaks.

 

 

 

 

 

 

 

 

Operate HANDLE up and down, left and right to flush water

A E R AT O R

 

 

 

 

 

 

lines thoroughly.

 

 

 

For faucet with spray, direct SPRAY HEAD into sink and

 

 

 

 

 

 

 

 

activate SPRAY. Check hose connections for leaks.

 

 

 

 

Move HANDLE down to "off" position and replace AERATOR.

 

 

 

 

 

 

 

 

 

CHECK CONNECTIONS

FOR LEAKS

6 SERVICEReduced flow. If the flow gradually reduces over a number of months, the AERATOR may have collected debris. To clean, remove AERATOR and rinse with water and remove any debris. Turn on faucet to wash any debris out of the faucet. Thread AERATOR back into spout. Operate faucet.

Spout leakage. If fitting leaks above or below SPOUT HUB remove SPOUT as follows and check SPOUT O-RINGS and SPACER O-RINGS.

Remove HANDLE BUTTON (2) and loosen SET SCREW (1). Pull HANDLE (3) off valve stem.

1 3

2 4

5

6

Remove CAP (4) and and RETAINER (5). Loosen CARTRIDGE SCREWS (6) and remove CARTRIDGE (7).

Pull off SPACER (8) and O-RINGS (9).

Remove SPOUT (12) by pulling up gently while moving SPOUT (12) side to side.

Check both SPOUT O-RINGS (11). Replace if necessary.

12

A E R AT O R

7

8

9

On models with SPRAYS, DIVERTER (10) can be cleaned by pulling

SPOUT

DIVERTER (10) out of the MANIFOLD (13). Clean DIVERTER (10) and

HUB

MANIFOLD (13). Push DIVERTER (10) back into MANIFOLD (10).

11

Reverse procedure to reinstall SPOUT, CARTRIDGE and HANDLE.

Clogged CARTRIDGE outlets or inlets may cause reduced flow.

13

To clean, first turn off water supply then:

Remove PLUG BUTTON (2), loosen HANDLE SCREW (1) and remove HANDLE (3).

Remove ESCUTCHEON CAP (4). unscrew the three CARTRIDGE SCREWS (6).

Clean inlets of CARTRIDGE (7) and MANIFOLD (13).

10

Reassemble CARTRIDGE (7), alternately tightening SCREWS (6). Replace CAP (4) and HANDLE (3). Check flow.

HOT LIMIT SAFETY STOP ADJUSTMENT

By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental scalding. To set the maximum hot water temperature of your faucets, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP.

"A"

PRY RED RING FORWARD AND ROTATE COUNTER- CLOCKWISE ONE CLICK

Remove HANDLE BUTTON (1) and loosen SET SCREW (2). Pull

TEMPERATURE

SETTING NUMBERS

HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade

 

"B"

 

screwdriver or your fingers to pull up and rotate red

 

 

PRY RED RING FORWARD

 

HOT LIMIT SAFETY STOP (5). Follow Step "A" or "B" to adjust AND ROTATE CLOCKWISE

min./max.discharge temperature. "0" being the hottest to

 

"B"

"B"

"7" the coldest temperature setting. Factory set at "0".

 

 

ADJUSTMENT WHEN

Replace ESCUTCHEON CAP (4), HANDLE (3), tighten

WATER IS TOO COLD

 

HANDLE SCREW (1) and install INDEX BUTTON (2).

 

 

 

 

 

 

"A"

"A"

 

 

 

 

0

ADJUSTMENT WHEN

 

 

 

1

 

 

 

4

 

2

 

 

WATER IS TOO HOT

3

 

 

 

5

 

 

 

 

 

 

6

 

 

 

 

 

6

 

 

 

 

 

 

5

"RED RING"- HOT LIMIT SAFETY STOP

M968955 REV . 1 . 2

Page 2 Page 3
Image 3
Page 2 Page 3
Contents Connoisseur Install Faucet with or Without Deck EscutcheonMake Water Supply Connections Connect Hose SprayHOT Limit Safety Stop Adjustment Test Installed Faucet

4400 SERIES specifications

The American Standard 4400 Series is a highly regarded line of toilets that combines style, quality, and innovative technology for optimal performance and user satisfaction. Renowned for its commitment to excellence, American Standard has incorporated several features into the 4400 Series that elevate it above other models on the market.

One of the standout characteristics of the 4400 Series is its WaterSense certification. This accreditation ensures that the toilet uses significantly less water without sacrificing performance, promoting environmental sustainability and helping homeowners save on their water bills. With a flushing system that effectively clears waste with only 1.28 gallons per flush, the 4400 Series demonstrates a perfect blend of efficiency and power.

The design of the 4400 Series is sleek and modern, making it an attractive addition to any bathroom decor. Its elongated bowl offers added comfort, while the high-profile tank provides a broader visual appeal. The toilet is available in various color finishes, allowing users to select one that complements their personal style and bathroom theme.

One of the key technologies featured in the 4400 Series is the EverClean surface. This innovative glaze helps to inhibit the growth of mold, mildew, and bacteria on the toilet's surface, making cleaning easier and more effective. As a result, maintenance is reduced, and the toilet retains its aesthetic appeal over time.

Additionally, the 4400 Series is designed with a three-inch flush valve, which is significantly larger than traditional valves. This enhancement increases the flushing power and helps to reduce clogs. Moreover, the toilet features a fully glazed trapway for improved waste removal, further enhancing its reliability.

Installation is simplified with the 4400 Series due to its standard design, which fits most plumbing configurations. The package includes the necessary hardware, making setup a straightforward process for both homeowners and contractors.

Overall, the American Standard 4400 Series exemplifies the perfect combination of style, efficiency, and strength. With its modern design, leading-edge technologies, and commitment to sustainability, it stands as a top choice for anyone looking to upgrade their bathroom experience. Whether for a new build or a remodel, the 4400 Series delivers on its promise of performance and reliability, making it an investment in both quality and convenience.
Top Page Image Contents