Presetting the Controls Before Use
Since sudden high output levels from your Pyle Pro mixer can damage not only audio devices connected to the mixer output but your hearing as well (especially if you are using headphones), please adjust the mixer’s controls BEFORE connecting AC power or turning on the unit.
Set up the mixer controls like this before you start:
CONTROL | SETTING | |
|
|
|
Power On/Off | OFF | |
Gain | MID |
|
Tone Controls, Treble, Mid and Bass | 0 |
|
MIC , CH 1/2 , Master and Cue Levels | 0 |
|
Crossfader | CENTER |
|
Connecting the Outputs
After presetting the controls (above), you can then connect the mixer’s output jacks to the output devices’ input jacks. Before connecting these devices, however, be sure to preset their controls to avoid any damage to your equipment due to unexpected high output levels.
Set the output devices’ controls like this before you start:
Connecting the Mixer Inputs
This mixer permits connection of up to five (5) audio input sources, including a microphone. Such a system might include, for example:
One Microphone | One Microphone | One Microphone | One Microphone |
Two Turntables | One Turntable | One Turntable | Two iPods |
Two iPods | Two iPods | One CD player | One CD player |
| One Cassette Deck | Two iPods | One Rhythm Synth |
|
| ||
Please observe | Connect any audio source with a HIGH LEVEL OUTPUT to the input 1 or | ||
input 2 mixer audio input jacks The selector or switch should be set to | |||
the following: | LN position. |
|
|
|
|
|
|
Connect audio inputs as follows:
|
| MIC | MIC Volume | High | Low |
| Mix | Cue Volume | Phones | |
1. DJ Microphone. Connect |
|
|
|
|
|
|
|
|
|
|
the DJ’s Microphone (not | DJ MIC |
|
|
|
|
| Fader Reverse |
|
| |
supplied) to the mic input jack. |
| 0 | MIC On | +dB | Off | On | 0 10 |
| ||
|
|
| 10 |
| Cue 1 Cue 2 |
| ||||
with a 1/4” plug .
Use 1/4” jack
OUTPUT DEVICE | CONTROL | SETTING |
|
|
|
Tape Deck | POWER | OFF |
Amplifier/Receiver | POWER | OFF |
| TONE | FLAT |
Playing the Mixer’s Output Signal
To play the mixer’s output signal through your speaker system (for events such as parties, dances, conferences, etc.) connect an audio patch cord with
2.High Level Output Audio Sources. Connect 2 sources (tuner, cassette deck, CD Player, camcorder or VCR) to the input jacks for input 1 and input 2. Please note that Phono and Line use the same jacks. The selector switch(e)s below the jacks should be set to Line position if the jacks are used for the High Level input sources described here.
Use RCA type patch cables
Master Record
Output Output
Power
L | L | GND |
USB 2
PH LN
RR
15V AC | Video Out 2 |
|
High Level Output
Audio Source
LEFT output
RIGHT output
Input 2 Input 1 |
|
| L | GND |
L | L | GND |
|
|
| PH | LN | PH | LN |
R | R |
| R |
|
|
|
|
| |
|
|
| Video Out 1 |
|
Vid
NOTE!
Be sure to place the input select switch(es) in positions which reflect what the connected input source is (Line in or Phono In)!
Recording the Mixer’s Output Signal
CD player, cassette deck, camcorder, VCR, etc.
To record the mixer’s output signal, connect audio patch cords (not supplied) from the mixer’s REC (Record) L and R jacks to your tape deck’s left and right input jacks.
3.Turntables. Connect up to 2 turntables to the input 1 and input
2jacks. Please note that Phono and Line use the same jacks. The selector switch below the jacks should be set to Phono position if the jacks are used for phono inputs.
Use RCA type |
| Input 2 | Input 1 |
|
|
| |
patch cables | L | GND L | L GND |
|
R | R | R | PH LN | L | GND |
PH | LN |
|
|
|
When using a turntable, you should also securely connect its ground wire (usually green or black) to the Ground screw on the input panel of the mixer.
Magnetic cartridge turntable
LEFT output
RIGHT output
GROUND wire from turntable
PH LN
R
Vid
2 – Pyle Pro Mixer Owner’s Manual | Pyle Pro Mixer Owner’s Manual – 3 |