Stovax Coal Effect Stove Range Main Injector, Primary Aeration Plate, Changing Between GAS Types

Page 23

 

 

SERVICING INSTRUCTIONS

 

 

REPLACING PARTS

 

 

8. MAIN INJECTOR

9.2

Refit a new sensor ensuring the spacers are located between

 

 

 

the sensor and the bracket. Replace the two leads.

 

 

 

9.3

If it has been necessary to remove the stove, ensure that all

8.1 Turn the gas supply off at the isolation device. Locate the

 

disturbed gas joints are checked for gas soundness when

 

reinstalled, and repeat the flue clearance test as detailed in

 

main injector on the LH side of the airbox, undo the

 

 

 

the Commissioning Section.

 

compression nut and pull the pipe clear of the injector

 

 

 

 

 

body, see diagram 13A.

 

 

 

 

 

 

10. PRIMARY AERATION PLATE

13

 

 

 

 

A

 

 

10.1

Turn the gas supply off at the isolation device.

 

 

10.2

Locate the aeration plate on the underside of the airbox

 

 

 

 

 

 

 

and remove the Nyloc nut, see diagram 15.

15

AR0389

8.2 Rotate the injector until it is fully removed, and install the

 

AR0381

correct replacement injector. Reassemble and turn the gas

 

supply on, check for leaks.

10.3 Remove the plate and replace with the correct size, ensure

 

 

 

 

 

that the hole(s) in the plate align correctly with the holes in

 

9. GAZCO FLUE SURE SYSTEM

 

the underside of the airbox and replace the Nyloc nut.

.

 

 

 

If the stove has been installed in a restrictive location, it

 

11. CHANGING BETWEEN GAS TYPES

may be necessary to remove the stove from its location.

 

9.1 Locate the sensor in the draught diverter opening, and

 

 

gently pull the two wires off the terminals. Undo the two

11.1 In order to change between gas types, it will be necessary

taptite screws and remove the sensor and the two plastic

 

to change the following items.

spacers. See diagram 14.

 

 

• Pilot Unit

 

 

 

14

 

 

• Control Valve

 

 

 

• Main Injector

 

 

 

• Aeration Plate (if required)

 

 

 

• Databadge

 

 

 

The relevant parts can be ordered as a conventional kit

 

 

 

from Gazco. Always quote the appliance type and serial

 

 

 

number when ordering spare parts.

 

 

 

** NOTE: THE CONTROL VALVE IS FACTORY PRESET

 

 

 

FOR CORRECT GAS TYPE AND MODEL. A NEW UNIT

 

 

 

WILL NEED TO BE ORDERED WHEN CHANGING

 

 

 

BETWEEN GAS TYPES.

 

 

 

 

23

Image 23
Contents Marlborough & Stockton Coal Effect Stove Range Contents GAS Check Appliance Commissioning ChecklistFlue Check Pass Fail Lighting the Appliance User InstructionsGeneral Fuel BED Arrangement Cleaning the FireTurning the Stove OFF Upgrading Your StoveSmall Marlborough and Stockton Medium Marlborough and Stockton Large Marlborough Running Installation DetailsGazco Flue Sure System Flame Failure DeviceTechnical Specification Installation InstructionsAppliance Location Installation of the GAS SupplySite Requirements Flue and Chimney RequirementsInstallation of the Stove InstallationControl Upgrade Safety PrecautionsClosure Plate Installation AR0360 Medium Marlborough and Stockton Large Marlborough Commissioning CommissioningServicing Instructions Servicing / Fault Finding ChartsFlame Failure Functional Check Fault Finding ChartsIgnition Functional Check Burner Unit Removal Replacing PartsPiezo Pilot UnitIgnition Lead and Piezo GAS Valve Magnetic Safety ValveChanging Between GAS Types Main InjectorPrimary Aeration Plate LPG Short Spares ListService Records Page Page Member of the Stovax Group