Univex 5100-02-IT, IT Series instruction manual Wiring terminations clean and correct

Page 27

Model 5100-02-IT Combustible Gas Sensor Module

•Wiring terminations clean and correct.

6.5.4MOISTURE TRAPS AND RAINSHIELDS

•Conduit seals and drains installed to avoid moisture build up in electronics enclosure. Water accumulation in sensor module enclosures is a major cause of damage and system failures - take precautions to seal electrical conduits and provide moisture traps and drains to avoid water damage

•Rain-shields installed where applicable.

6.5.5STANDARD VOLTAGES

•Regulated DC Voltage to be applied to the sensor module must be between 10 VDC and 30 VDC.

6.5.6INSPECTION AND TROUBLESHOOTING GUIDE

The inspection and troubleshooting guide can be used to step through the system start-up and to determine the corrective action if a fault occurs.

6.5.7IF MODULE DOES NOT RESPOND TO GAS

1.Repeat calibration procedure.

2.Remove the gas and wait for the timer to completely count down.

3.Apply 50%LEL and verify that the sensor sees 50% LEL gas after calibration.

4.If the sensor still does not see gas, power cycle the unit and repeat calibration.

6.5.8IF THE MODULE DOES NOT COME OUT OF WARM UP

1.Make sure the sensor is placed in an ambient room temperature environment.

2.Power cycle the sensor.

3.Ensure that the sensor is not exposed to combustible gas during warm-up.

6.5.9IF THE MODULE DOES NOT DISPLAY THE CORRECT %LEL

1.Power cycle the unit.

2.Recalibrate the sensor.

6.5.10IF THE DISPLAY SHOWS ‘NO SENSR’ –SENSOR FAILING

1.Power down the unit

2.Open the enclosure and unplug the sensor from the transmitter board.

3.Plug the sensor back into the transmitter board carefully and ensure a secure fit.

4.Power up the unit.

6.5.11IF THE MODULE SHOWS “***CALIBRATION REQUIRED***”

1.Calibrate the module

6.5.12IF THE MODULE SHOWS “***UNCALIB***”

1.Hold magnet to any key to acknowledge message

2.Calibrate the module

6.5.13IF THE DISPLAY SHOWS ‘H’ (OR L) THEN THE LOCAL HIGH OR LOW ALARM IS ACTIVE

6.5.14IF THE DISPLAY SHOWS ‘W’ – RADIO FREQUENCY INTERFERENCE

1.Remove source of interference.

6.5.15IF THE DISPLAY SHOWS “C” – CALIBRATION MODE

1.Complete calibration or exit to operating mode.

6.5.16OTHER ERROR MESSAGES – CALL FACTORY

1.E: OSC F1 Oscillator Fail

Page: 25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Applicability & Effectivity IT SeriesFM Approval Model 5100-02-IT Combustible Gas Sensor ModuleCalibration Equipment Table of Contents If the Module Shows ***UNCALIB Theory of Operation Product ConfigurationProduct Description GeneralModel 5100-02-IT Combustible Gas Sensor Module Mechanical Power Requirements Interconnect WiringIntroduction IT Modules General WiringCatalytic Bead Sensor Modules Sensor Module Locations InstallationEnclosure Installation Sensor Module External Interfaces Connector Locations Installation ConfigurationMA Connection Digital Interface Connections Remote Alarm Reset Introduction HUMAN-MACHINE Interface System HUMAN-MACHINE InterfaceEnter Describes the primary human-machine interface operation Main MenuConfigure SET-POINTS 3A Set-Up Configuration Relays Set Point Adjustment ExampleGas Factor Example MA Adjustment ExampleRS-485 Adjustment Example Set-Up ConfigurationMaintenance Menu Maintenance FunctionsModel Gas Flow Period CalibrationSub-Routine a Abort Calibration Module Components ServiceTransmitter Replacement Wiring terminations clean and correct Appendices Appendix a SpecificationsSensor Module Appendix B Model Numbers & Parts ListAppendix C Limited Warranty Appendix D Remote Sensor Drawing Appendix E Auxiliary Relay Assembly Appendix F Auxiliary Connection Assembly Appendix G Auxiliary RS-485 Multidrop Assembly Model 5100-02-IT Combustible Gas Sensor Module Appendix H Modbus Memory MAP Read Register Table DescriptionComments GAS Methane Factor Appendix I Combustible GAS Scaling FactorsAlarm Reset Menu Appendix J Menu Key for 5100-02-IT Gas Sensor ModuleCalib Menu Setup Menu Maint Menu This page Intentionally Left Blank

5100-02-IT, IT Series specifications

The Univex 5100-02-IT, part of the IT Series, is a highly advanced piece of technology designed to cater to a myriad of industrial applications. This product stands out for its impressive features and robust performance, making it a sought-after solution in various sectors.

One of the key characteristics of the Univex 5100-02-IT is its versatility. Designed with a modular architecture, it allows for easy customization according to specific operational needs. This flexibility supports an extensive range of configurations, ensuring that users can optimize performance based on their unique requirements.

In terms of connectivity, the Univex 5100-02-IT excels with its comprehensive array of communication options. It supports multiple protocols, including Ethernet, Wi-Fi, and serial communications, ensuring seamless integration with existing systems. This adaptability facilitates efficient data exchange and helps streamline operations, whether in manufacturing, logistics, or other industrial settings.

The IT Series emphasizes reliability and durability, which are critical in industrial environments. The 5100-02-IT is built with high-quality materials that can withstand harsh conditions, including temperature fluctuations and exposure to various chemicals. This robustness ensures minimal downtime and adds to the overall efficiency of operations.

Another standout feature of the Univex 5100-02-IT is its advanced data processing capabilities. Equipped with a powerful processor, it ensures quick and accurate analysis of data, enhancing decision-making processes. This allows organizations to respond faster to changing conditions and optimize their operations in real-time.

Security is paramount in the current technological landscape, and the Univex 5100-02-IT addresses this concern with a suite of security features. With built-in firewalls and data encryption capabilities, it safeguards sensitive information against unauthorized access and cyber threats.

User-friendliness is also a priority with this device. The intuitive interface makes navigation simple, allowing operators to efficiently manage settings and monitor performance with ease. This simplicity reduces the learning curve and enhances overall productivity.

In summary, the Univex 5100-02-IT from the IT Series embodies a range of advanced features, technologies, and characteristics that cater to the evolving demands of industrial applications. Its versatility, robust construction, reliable connectivity, advanced data processing, security measures, and user-friendly interface make it an invaluable asset for companies looking to enhance their operational efficiency and adaptability.
Top Page Image Contents