Model KKFV01LP

3.Working from under the sink or countertop, reinstall the parts onto the threaded shank of the faucet in the following order: flat rubber washer, white triangular support, flat metal washer, and threaded collar.

	A
	B
	C
	D
A. Flat rubber washer	C. Flat metal washer
B. White triangular support	D. Threaded collar

4.Align the faucet and firmly hand-tighten the threaded collar to keep the faucet base from turning when moving the control lever. Make sure the control lever is pointed toward the right- hand side of the sink.

5.Connect the sprayer hose to the water supply hose using the check valve assembly and the fiber washers. Make sure the check valve assembly is positioned so that the arrow is pointing down, away from the faucet and toward the sprayer head.

6.Place a fiber washer between the sprayer hose and the check valve assembly and fasten them together. Then, place a fiber washer between the check valve assembly and the supply hose and fasten them together, as shown.

	A
	B
	C
	D
	E
A. Supply hose (from faucet)	D. Fiber washer
B. Fiber washer	E. Sprayer hose
C. Check valve assembly

7.Connect the red-striped, braided hose to the hot water supply valve. Connect the blue-striped, braided hose to the cold water supply valve. Hold the hoses in place when tightening the nut to keep the hoses from twisting.

8.Make sure the sprayer hose is fully inserted into the faucet body.

9.Working from under the sink, use the screws provided to attach the weights onto the sprayer hose. Attach the weights to the sprayer head side of the hose loop, just above the bend in the hose, as shown.

NOTE: The weights are for counterbalance only, not for automatic retraction.

C	A
C
	B
A. Weights	C. Water flow direction
B. Sprayer hose

10.Move the faucet lever to the closed (forward) position and open supply valves. Check connections for leaks.

11.Remove the aerator from the faucet and flush the hot and cold lines until water is clear.

NOTE: The aerator is in the end of the faucet. To remove and replace aerator, see “Aerator Assembly” in the “Faucet Care” section.

12.Reinstall the aerator into the faucet and tighten with a wrench.

1.Remove the threaded collar, flat metal washer, and flat rubber washer from faucet.

NOTE: Do not remove the rubber O-ring from the bottom of the faucet base.

	A
	B
	C
	D
A. Rubber O-ring	C. Flat metal washer
B. Flat rubber washer	D. Threaded collar

2.Feed tubing through the hole in the sink or counter top and then insert threaded shank into the hole. Make sure the rubber O-ring in the channel at the bottom of the faucet base is firmly in place.

	A
	B
	C
	D
A. Flat rubber washer	C. Flat metal washer
B. White triangular support	D. Threaded collar

4.Align the faucet and firmly hand-tighten the threaded collar to keep the faucet base from turning when moving the operating lever.

5.Connect the red-striped, braided hose to the hot water supply valve. Connect the blue-striped, braided hose to the cold water supply valve. Hold the hoses in place when tightening the nut to keep the hoses from twisting.

6.Move the faucet lever to the closed (forward) position and open supply valves. Check connections for leaks.

7.Remove the aerator from the faucet and flush the hot and cold lines until water is clear.

NOTE: The aerator is in the end of the faucet. To remove and replace aerator, see “Aerator Assembly” in the “Faucet Care” section.

8.Reinstall the aerator into the faucet and tighten with a wrench.