Radio Shack HTX-400 owner manual Understanding Repeaters

Page 26

UNDERSTANDING REPEATERS

Operation through a repeater, where you transmit on one fre- quency and receive on another, is called duplex operation. Oper- ation direct to another station, where you transmit and receive on the same frequency, is called simplex operation.

A repeater is a station that receives a signal on one frequency (the input frequency) and then retransmits that signal on a differ- ent frequency (the output frequency). Repeater antennas are typ- ically located at the tops of tall buildings or on antenna towers, so a relatively low-power signal can reach the repeater. The repeat- er retransmits the signal at a higher power. This gives your trans- ceiver the ability to communicate over a much greater range.

To use a repeater, you must know the repeater’s input and output frequencies. Repeaters are usually identified by their output fre- quency. Thus, a repeater that has an output frequency of 442.200 is referred to as “the 442.2 repeater.” To determine the input fre- quency, you must know the frequency offset (typically 5 MHz for the 70 cm-meter band) and the offset direction (+ if you add 5 MHz to the output, or – if you subtract 5 MHz from the output).

Whether the offset is positive or negative depends on:

•which part of the band the repeater operates on

•local convention

•proximity of repeaters using the same two frequencies

To determine the offset and the direction, obtain a copy of The ARRL Repeater Handbook (available from your local Ra- dioShack store or directly from the ARRL) which lists the loca- tions of repeaters as well as their frequency and offset information.

A + above the displayed frequency indicates a positive offset, while a – above the frequency indicates a negative offset. If nei- ther + nor – appears, the HTX-400 is set for simplex operation.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents HTX-400 Features Ctcss Manual Conventions FCC InformationContents Continuous Tone Coded Squelch System Features Introduction to Amateur Radio Page Power Sources PreparationTesting Internal Batteries Using AC Power Using NI-CD or NI-MH Battery PowerUsing Vehicle Battery Power Connecting the Antenna Attaching the Belt ClipConnecting a MICROPHONE/ Speaker Attaching the Wrist StrapPTT Using the Menus Using the HTX-400’S MenusTot Tone Set Setting Option = default setting Description Quick Look AT the Controls Use it to Func + Key toMO REV VOL, and SQ Quick Look AT the Display Held down at the same timeTurning on the HTX-400 Selecting Frequencies Direct TuningOperation Receiving Transmissions Temporarily Opening SquelchTransmitting Understanding Repeaters Setting the Repeater Offset Frequency Turning Duplex Operation on and OFFSetting the Repeater Offset Direction Reversing the Transmit and Receive FrequenciesMemory Operation Storing a TRANSMIT/RECEIVE FrequencyRecalling Memories Clearing a Single MemoryUsing the CALLING-FREQUENCY Memory Scanning Standard Memory Locations Scanning OperationScanning for Active Frequencies Setting a Memory Location to Always Skip During Scanning Page Continuous Tone Coded Squelch System Features Subaudible Tone Frequencies Hz Tone Paging Sending Paging TonesLocking the Keypad Other Special FeaturesChanging the Transmit Frequency Range Lighting the DisplayTurning the KEY Tone on and OFF Checking the Current Memory SettingsSetting the Frequency Step Power Save TIME-OUT TimerReducing Squelch Tail Busy Channel LockoutTroubleshooting You see Possible Cause RemediesCare and Maintenance Using the Keypad Diagnostic Resetting the HTX-400Specifications GeneralPage Page Limited One-Year Warranty

HTX-400 specifications

The Radio Shack HTX-400, introduced in the mid-1990s, remains a beloved model among amateur radio enthusiasts and collectors. Known for its reliability and versatility, this transceiver is particularly notable for its compact design and user-friendly interface. The HTX-400 operates on both VHF and UHF frequencies, enabling users to communicate effectively across various channels.

One of the HTX-400’s key features is its output power, which is adjustable between 1 and 40 watts. This flexibility allows operators to choose their transmitting power based on the communication needs and conditions of their environment. The device operates on the 2-meter band, covering the frequency range of approximately 144 to 148 MHz, making it ideal for local communications as well as a part of emergency communication networks.

A significant technological aspect of the HTX-400 is its digital display, which provides clear readings of frequency and signal strength. Users appreciate the intuitive control layout, which allows for quick adjustments and easy channel changes. The built-in memory function can store multiple frequencies, providing users with the ability to switch quickly between channels they use frequently.

Another standout feature is its CTCSS tone encoding and decoding capability. This allows operators to filter incoming signals and communicate within designated groups without interference from other conversations on the same frequency. This capability enhances clarity and reduces noise, making it an excellent choice for repeaters.

The HTX-400 also includes an Automatic Gain Control (AGC) feature, which adjusts the receiver automatically to varying signal strengths, ensuring consistent audio quality even in weak signal conditions.

Portability is a major consideration for amateur radio operators, and the compact size of the HTX-400 makes it easy to transport. It operates effectively with various power sources, including a standard AC power supply and battery, making it a suitable option for both home use and portable operations.

In conclusion, the Radio Shack HTX-400 is a versatile and reliable transceiver that features adjustable power output, user-friendly controls, memory functions, CTCSS tone capabilities, and excellent portability. Its combination of advanced technologies and practical design has made it a favorite among radio enthusiasts for decades.
Top Page Image Contents