Jackson Whirl Wizard INSTALLATION/OPERATION Instructions, Installation Instructions

Page 11

SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

VISUAL INSPECTION: Before installing the unit, check the container and machine for damage. A damaged container is an indi- cator that the machine may have been hadled roughly during shipping. If there is damage to both the container and the machine, do not throw away the container. The machine has been inspected at the factory and is expected to arrive to you in new, undamaged condition. However, rough handling by carriers or others may have resulted in damage occuring to the machine. If such a situation does occur, do not return the unit to Jackson. Instead contact both the dealer you purchased the unit through and the carrier. Ask the carrier to send a representative out to inspect the damage and make a report of it. You normally have 48 hours to contact a carrier to report damages, but this varies based on locale. The best advice is to contact your carrier and dealer as soon as damage is discovered.

UNPACKING THE MACHINE: Once the machine has been removed from the container, ensure that there are no obvious miss- ing parts. This may not be apparent at first glance. If you discover that a part is missing, contact Jackson MSC Inc. immedi- ately.

LEVEL THE MACHINE:

1.Position the Whirl Wizard under the sink drainboard.

2.Adjust left to right and front to back.

3.Align inlet and outlet tubes with plumbing from main flow chamber (item 2).

4.To adjust the height, loosen the allen screws in each leg socket connector.

5.Slide leg out to desired height. The drain connection on the machine should be at the same level as the sink drain connec- tion.

6.Tighten the allen head screws in each leg socket connector.

7.Fine adjustments in height can be made by turning the bullet foot in each leg.

INSTALLING THE MACHINE:

1.Locate the sink at the highest end of the drain slope.

2.Disconnect the existing drain plumbing from the sink.

3.Remove the crumb cup.

4.Clean off old plumber’s putty from the sink. Add fresh putty to the sink flange.

5.Position the main flow chamber (item 2) through the bottom of the sink. From the bottom, slip the rubber washer (item 3), fiber washer (item 4), back-up flange (item 5) and mounting flange (item 6) on the main flow chamber.

6.Once in position, mount the jam spring (item 7) on to the main flow chamber. This will hold items 3 through 5 in place.

7.Tighten the screws in item 6 until the assembly is held in place. Care must be taken to position screws where they are acces- sible and will not be covered by the hose barb when assembled into the main flow chamber.

8.In the bottom of the main flow chamber (item 2), install the 1-1/2” NPT close nipple (item 10).

9.The 1-1/2” NPT tee (item 9) is screwed onto the 1-1/2” nipple (item 10).

10.From the tee (item 9) to the drain, install the following items: 1-1/2” close nipple (item 10) and 1-1/2” ball valve (item 11). Make sure the handle of the ball valve (item 11) is easily accessible by the operator.

11.On the sink side of the tee (item 9) install a 1-1/2” NPT hose barb (item 12).

12.On the inlet side of the main flow chamber (item 2) install a 1” NPT hose barb (item 8).

13.With different styles and types of sinks, the directional manifold (item 1) may require modification. The directional tubing may need to be bent to conform to the bottom of the sink or reduced in length. Since it is fabricated from thin wall stainless steel, a hacksaw can be used to cut the tubing.

HOSE CONNECTIONS:

1.Position the 1-1/2” ID intake line hose (item 13) with the Whirl Wizard as xlose to the sink as possible, mark and cut to the length required.

2.Repeat with the 1” ID discharge line hose (item 14).

3.Connect the intake and discharge line hoses with hose clamps (item 15) to their respective connections.

NOTE: ENSURE THAT THE HOSE CLAMPS ARE TIGHT BEFORE OPERATING THE UNIT.

CAUTION: IF DIRECT FLOOR DRAIN IS UNDER OR NEAR MACHINE, MAKE CERTAIN THAT ADEQUATE PROTEC- TION IS PROVIDED TO PREVENT WATER SPLATTER FROM DAMAGING THE UNIT.

Whirl Wizard Technical Manual 7610-011-70-65

Issued: 08-20-2007 Revised: N/A

5

Page 10 Page 12
Image 11
Page 10 Page 12
Contents For Jackson Model Whirl Wizard INSTALLATION/OPERATION Technical ManualONE Year Limited Parts & Labor Warranty Manufacturers WarrantyStop Pare Arret MAW Revision Made Applicable Details Date ECNNomenclature for the Models Covered in this Manual AJ-54CETable of Contents Section Specification Information Electrical Requirements Specification InformationWhirl Wizard Dimensions Section Installation & Operation Instructions Level the Machine INSTALLATION/OPERATION InstructionsInstallation Instructions Installing the MachineInstallation Instructions Electrical Power Connection Operation Instructions Cleaning InstructionsChanging Direction of Machine Installation Section Preventative Maintenance Preventative Maintenance Preventative MaintenanceSection Parts Section Parts Section Installation AssemblyTEM QTY Description Main AssemblySection Electrical Diagrams Sequence of Operation Electrical SchematicsWhirl Wizard 115 Volt 60 HZ Single Phase Whirl Wizard 240 Volt 50/60 HZ Single Phase Section Jackson Maintenance Repair Centers Alabama to Florida Jackson Maintenance & Repair CentersFlorida to Maryland Maryland to NEW York NEW York to Pennsylvania Rhode Island to Wisconsin Sheldon and CO Metro Appliance Service 1640 S Broadway DENVER, COWisconsin to WYOMING/INTERNATIONAL International Global Parts and Supply 7758 NW 72ND ST

Whirl Wizard specifications

Jackson Whirl Wizard is a dynamic and innovative product that has captivated the market with its unique features and advanced technologies. Designed for versatility and excellence, the Whirl Wizard is primarily targeted at both professional users and hobbyists who require high performance while engaging in a range of activities.

One of the defining characteristics of the Jackson Whirl Wizard is its robust design. Built with high-quality materials, it ensures durability and longevity, making it perfect for both indoor and outdoor use. This resilience does not compromise the product's lightweight nature, allowing users to easily transport it wherever they go.

The core technology of the Whirl Wizard lies in its powerful motor. This motor provides an impressive speed range, allowing users to customize their experience based on their needs. Whether it's for precision tasks or high-speed applications, the Whirl Wizard can adapt effectively. Its energy-efficient design also ensures minimal power consumption without sacrificing performance.

Another significant feature of the Jackson Whirl Wizard is its intuitive control system. Users can effortlessly switch between modes and adjust settings through a user-friendly interface. This accessibility makes it suitable for individuals of all skill levels, from beginners to experts, enabling everyone to harness its full potential.

Safety is a paramount concern for Jackson, and the Whirl Wizard reflects this commitment. Equipped with advanced safety features such as automatic shut-off and overload protection, users can operate the device with peace of mind, confident that they are protected from potential hazards.

The Whirl Wizard also includes a variety of attachments that enhance its functionality. These accessories can be easily swapped out, enabling users to tackle different tasks efficiently, such as mixing, blending, and even crafting. The versatility offered by these attachments is one of the key reasons why users praise this product.

In conclusion, the Jackson Whirl Wizard stands out in the market due to its combination of robust design, advanced motor technology, user-friendly controls, and a commitment to safety. Its versatility makes it an ideal choice for those seeking reliability and performance in their projects, whether casual or professional. With the Jackson Whirl Wizard, users are empowered to unleash their creativity and achieve exceptional results in their tasks.
Top Page Image Contents