Grizzly G0572 Flush Mount, Optional, To install the air filter for flush mount operation

Page 19

2.Remove the plug screw. Retain the screws, because if you remove the eye bolts for the flush mounting configuration, you must reinstall these screws to seal the air filter unit. (Figure 10).

Plug Screw

Figure 10. Plug screw.

3. Thread the eye bolt completely into the air filter unit until the shoulder contacts the air filter unit (Figure 11).

Eye Bolt

Figure 11. Eye bolt correctly seated.

4.Tighten the eye bolt until it is snug against the air filter unit.

5.Repeat Steps 2-5on the three remaining eye bolts.

6.Raise and secure the air filter eye bolts to the four hanging lines.

Flush Mount

 

Components and Hardware Needed

Qty

Mounting Brackets

4

Hex Bolts 1⁄4"-20 X 1⁄4"

8

Optional

 

1⁄4" Lag Bolts

4

1⁄4" Nuts

4

1⁄4" Bolts

4

1⁄4" Flat Washers

4

Tools Needed

 

Wrench 10mm

1

You can install the air filter unit in a confined shop by mounting it flush to a ceiling, wall, or table using the flange mounts.

ONLY mount the air filter unit to load bearing joists, wall studs, or table that can hold at least 100 lbs. DO NOT mount the unit to sheet rock walls, pressboard, paneling, or honeycomb wall panels with expansion- type fasteners like the ones shown in Figure 9. The fasteners can tear out and the air filter can fall. Ignoring this warning can result in severe injury or death.

Get

lifting

assistance

before installation. At

64

pounds

(shipping

weight), the Model G0572

air filter is a heavy load.

To install the air filter for flush mount operation:

1.Locate the applicable load bearing studs or supports in the wall or ceiling, and mark the air filter unit bolt pattern on the wall or ceiling (171⁄4" from left-to-right and 31" from front-to-

rear).

G0572 Hanging Air Filter with Remote

-17-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Hanging AIR Filter With Remote Page Table of Contents Foreword IntroductionContact Info Capacities Overall DimensionsSafety Instructions for Machinery SafetyAlways Lock Mobile Bases Before Operating Machinery Additional Safety for Hanging Air Filters 110V Operation Circuit RequirementsGrounding Unpacking SET UPSet Up Safety Items Needed For Set UpInventory Remote Control and Mounting HardwareComponents Figure Hardware Recognition Chart Site Planning Shop PreparationTo calculate the recirculating rate for your Filter CapacityShop space Mounting Preparation Dust SystemBeginning Mounting To set up the air filter for table-top operationComponents and Hardware Needed Qty Air filter is a heavy load To install the air filter for hanging mount operationsHanging Mount Tools NeededFlush Mount To install the air filter for flush mount operationOptional Page Control Panel Operation SafetyOperations OverviewTo operate the air filter unit, use the listed controls Remote ControlAccessories To operate the remote control unit, use the listed controlsBlow out the secondary filter. If you do, you will MaintenanceFilters Air toG0572 Wire Diagram G0572 Parts Breakdown G0572 Parts List Symptom Possible Cause Possible Solution TroubleshootingWarranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog

G0572 specifications

The Grizzly G0572 is an advanced wood planer that has gained recognition among woodworking enthusiasts and professionals for its powerful performance and exceptional features. Engineered for efficiency and precision, the G0572 offers a range of capabilities that make it a standout choice for anyone looking to enhance their woodworking projects.

One of the most notable features of the Grizzly G0572 is its powerful 5 HP motor, which provides ample power to handle even the toughest of hardwoods with ease. This ensures consistent performance and efficiency, allowing users to process large quantities of material without experiencing a slowdown. Additionally, the motor is equipped with a motor overload protection feature, ensuring the longevity and reliability of the tool.

The G0572 incorporates a sizable 12-inch cutting width and a depth of cut that allows for smoothing rough lumber and achieving precise finishes. It features a helical cutter head with 36 individual insert knives, enabling users to achieve a smoother finish while significantly reducing noise levels compared to traditional straight knife designs. This helical design also contributes to longer tool life, as the inserts can be rotated and replaced easily when dull.

The build quality of the Grizzly G0572 is another highlight, featuring a robust cast iron construction that provides excellent stability and reduced vibration during operation. This durability translates into a longer lifespan for the machine, making it a worthwhile investment for serious woodworkers.

In terms of user convenience, the G0572 includes a large infeed and outfeed table, which helps support longer stock and ensures smooth passage through the planer. The integrated dust collection port is another feature that aids in maintaining a clean workspace, allowing for efficient dust management during operation.

Overall, the Grizzly G0572 combines power, precision, and advanced technology to deliver outstanding performance in woodworking applications. Its robust features and thoughtful design make it an excellent choice for professionals and hobbyists seeking a high-quality wood planer that can handle a variety of tasks with ease and reliability. Whether you are flattening rough lumber or achieving the perfect finish, the Grizzly G0572 is a tool designed to meet the demanding needs of modern woodworking.
Top Page Image Contents