Ramsey Electronics HR40 manual PIN Count Megoh

Page 23

frequency response, but is does significantly boost the output of the SA602 reaching the LM386 audio amplifier IC. Instead of the traditional transistor audio preamp circuit, an additional LM386 is used in its minimum gain configuration (gain of 40), plus one electrolytic capacitor (1 to 10 uF) to achieve minimum parts and PC-board drilling. This use of two LM386 ICs amplifies the audio signal of the SA602 by a factor of 1000.

This modification requires cutting the circuit trace leading from C8 to the

 

27

 

NE60

pF

TO

 

2

 

 

PIN

1

COUNT

7

ER

 

MEGOH

 

M

volume control, R3.

Additional LM386 used as AF preamplifier between U1 and U2:

ˆPins 1,7,8: not used

ˆPins 2,4: to ground

ˆPin 3 to ‘-’ side of c*(2.2 pF)

ˆPin 5 to ‘+’ side of new 1 to 10 uF capacitor

ˆPin 6 to ‘+’ DC supply board trace

The ‘-’ side of the new capacitor is connected to the circuit trace leading to the volume control. Mount this capacitor as close to the body of the new LM386 as possible. Keep all leads as short as possible. This modification results in very good speaker volume but will also require closer attention to battery quality and condition or else the audio circuits will cause oscillator instability. Two alkaline cells in parallel or a 12 volt supply are recommended. If the gain is too much, use a resistor to reduce the voltage supplied to pin 6 of preamp LM386

Finally, we remind you again that modification of any PC board puts you on your own, voiding your factory warranty, making your unit ineligible for factory repair. Make sure the receiver is working properly and that you understand how to use and repair it BEFORE making any changes in the original design. Enjoy it!

HR40 • 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents ALL Mode Receiver KIT Ramsey Transmitter Kits HR40 Amateur Receiver KIT Ramsey HR-SERIES Amateur Receivers IntroductionAbout Direct Conversion Receivers Circuit Description Capacitors Parts Supplied with the HR40 KITLEARN-AS-YOU-BUILD Assembly Strategy HR40 Parts Layout Receiver Assembly Page Page Required for Initial Testing and Alignment Initial Testing of Your HR40Alignment Hint for ALL Direct Conversion Receivers AlignmentOn the AIR TRANS-RECEIVING Using Your ReceiverTuning SSB Signals CW OperationSpeaker Operation More Audio Power Another WAYAdding AN LED Power on Indicator Page Troubleshooting Tips General Notes for Experienced QRP Builders Alternate Power SourcesBandspread and Tuning Range Frequency Stability LM386 Audio Output Other Methods of Dial CalibrationDirect Frequency Readout PIN Count Megoh Construction Notes HR40 Ramsey Kit Warranty Factory Repair of Assembled Kits Additional Suggested Items Total Solder Points Estimated Assembly TimeHR40 Amateur Receiver KIT Required Tools

HR40 specifications

The Ramsey Electronics HR40 is a versatile and high-performance FM transmitter that has gained recognition among hobbyists and professionals looking to broadcast audio signals. With its robust features and user-friendly design, the HR40 stands as an excellent choice for a range of applications, from low-power broadcasting to personal audio projects.

One of the standout features of the HR40 is its frequency range, typically allowing for transmission on the FM band from 88 to 108 MHz. This broad range ensures compatibility with a variety of receivers and allows users to select an optimal frequency for their needs, minimizing potential interference. The transmitter is designed to offer excellent audio fidelity, with a frequency response that meets and exceeds industry standards, ensuring clear and crisp sound quality.

The HR40 utilizes advanced modulation techniques, which contribute to its performance in terms of signal clarity and range. The use of frequency modulation allows the HR40 to transmit audio signals with minimal distortion, even at higher volume levels. Additionally, the transmitter is equipped with a built-in audio preamplifier, which enhances audio quality by providing a clean and powerful signal before transmission.

Another notable characteristic of the HR40 is its adjustable output power. Users can modify the power level to suit their specific broadcasting needs, whether for indoor use or outdoor applications. This flexibility is particularly useful in managing transmission range, allowing users to tailor their setup without excessive overkill or underperformance.

The compact design of the HR40 also stands out, making it a popular choice for those who need a portable broadcasting solution. The unit is lightweight and easy to transport, while its durable construction ensures longevity and resilience in various environments.

In terms of ease of use, the Ramsey Electronics HR40 offers simple installation and operation. It comes with a clear instruction manual, allowing users to set up their transmitters quickly. The intuitive interface and minimal setup requirements enable beginners to jump right in, while advanced users can take advantage of its expandability and customization options.

Overall, the Ramsey Electronics HR40 combines user-friendliness with a range of powerful features aimed at both amateur and experienced broadcasters. Its excellent audio quality, adjustable output power, and compact design make it a favorite for many seeking reliable FM transmission capabilities.
Top Page Image Contents