Table of Contents

Your New PYLE PPA series P.A. Amplifier gives you the power and versatility you need in a professional sound system.

The amplifier's wide frequency response makes it suitable for amplifying music or vocal program material. It can be used for live bands, office paging systems, public announcements, or a variety of other installations.

1Features and Controls,

2 Installation Guidelines

2 Input Connections

2 Connecting a CD, DVD or tape player or tuner 2 Connecting an equalizer or signal processor 2 Stereo or Mono Inputs

2 Speaker connecitons

3 Bridged Mode Operation

3 Connecting to standard AC power

3 Mounting the amplifier

3 Turning the amplifier on

3 Using the power LED meter

3 Using the channel1 and channel2 output level controls

3 About the internal clip circuitry

4 Specifications Limited warranty

INSTALLATION GUIDELINES

Connecting the GND (Ground) screw terminal Connecting a mixer or preamplifier may cause excessive noise or hum in the amplifier output. To prevent this, connect one end of a low-capacitance shielded wire to the amplifier’s ground screw (on the rear panel). Then connect the other end of this wire to the ground terminal on the mixer or preamplifier enclosure.

	PREAMP OR MIXER
LOW CAPACITANCE SHIELDED WIRE	GROUND
	SCREW

Input connections

Stereo or Mono Inputs

Your PYLE PPA amplifier can be operated in Stereo, Mono or Bridged mode, depending on the input source. If the input signal is mono, slide the Stereo/Mono/Bridged selector switch to MONO and the signal will be routed through both channels. If you wish to run the amplifier in bridged output mode, slide the switch to Bridged.

Speaker connections

You can connect 4 Ohm, 8 Ohm or 16 Ohm speakers to Channel 1 and/or Channel 2 of the amplifier. If you connect two pairs of speakers, be sure to follow these guidelines:

• Speakers which are connected to the same channel are

part of a pair, and must be of the same impedance.

• Speakers connected to different channels are NOT part

Please read this manual throughly before you attempt to set up and use the amplifier. It contains a range of installation suggestions as well as instructions to ensure safe usage. Installed properly, you can expect years of trouble-free service from this product.

Channel 1 and Channel 2 Power LED Display

FEATURES AND CONTROLSIndicate the output signal level for each channel.

FRONT PANEL, PPA200, PPA300, PPA450

PPA450

4500 Watt

These amplifiers accept a broad range of input sources, including Compact Disc (CD) players; DVD, Cassette, Reel- to-Reel or other tape players; Radio Tuners; Equalizers; Signal Processors.

Connecting a CD or DVD or tape player or tuner

In a normal installation, one would use the RCA JACKS for connecting a CD player, DVD, tape player or tuner.



	INPUTS	OUTPUTS	VOLTAGE
CH-2	CH-1	CH-2	CH-1

GND

use RCA jacks	CD PLAYER, DVD , TAPE PLAYER
	OR TUNER

of a pair, and can be of different impedances.

1.Prepare the speaker wire by removing about 1 inch of insulation from the end of the speaker wire you intend to connect to the amplifier. Then twist the exposed wire to secure all the wire strands.

NOTE: Use 16-gauge speaker wire for lengths up to25 feet; 14-gauge wire for lengths over 25 feet. It is recommended that you use the shortest length of wire possible.

2.Connect the speaker wires to the speaker's positive and negative terminals.

NOTE: Most speaker terminals are either color-coded or have a mark that indicates the terminal's polarity. Usually positive terminals are red or have a plus symbol (+), and negative terminals are black or have a minus symbol (-).

Power On/Off

Channel 1 and Channel 2

Output Level Controls

Lets you adjust the sound levels for each channel.

Fan Cooling

Cooling system is automatically activated whenever amplifier is turned on. This forced air cooling system rapidly exhausts interior heat, reducing operating temperature and aiding performance.

Protection Circuit and Indicator

The indicator will be illuminated when the amplifier is powered on and at turn- on delay status; the indicator will be turned off after internal outputs are connected. The indicator will also be illuminated when the amplifier has abnormal problems, such as overload or excessive heat.

Connecting an equalizer or external signal processor Connect the processor’s OUT to the amplifier’s INPUT connectors.

EQ OR MIXER

3.Connect the speaker wires to the amplifier's left and right speaker terminals according to the terminal color polarity.

STEREO OPERATION

SWITCH IN “STEREO” POSITION

REAR PANEL, PPA200, PPA300, PPA450

						B A)L A-)N C E D I N P U T S
							HO T ( + CO L D (	GN D
							HO T ( + CO L D (	GN D
		INPUTS
CH-2	CH-1
			CH-1	MONO
			STEREO		BRIDGE
GND							GROUND LIFT

CH-2

LIFT

	OUTPUTS	VOLTAGE	POWER CONSUMPTION :
CH-2	CH-1		~AC iN
CH-2	CH-1		115/230V- 60/50 Hz

BRIDGE

FUSE

INPUTS

CH-2CH-1

GND

-OR–

OUTPUTS

VOLTAGE

CH-2 CH-1

EQ OR MIXER

use XLR/6.35 mm combo jacks

INPUTS

CH-2CH-1

GND

CH 2	CH 1

OUTPUTS	VOLTAGE
CH-2	CH-1

STEREO SIGNAL SOURCE

Input Jacks	Stereo/Mono Switch
Let you connect a variety of audio	Lets you select conventional
input sources via the balanced	stereo operation with a
(XLR/6.35mm phone jack	stereo input signal or bridged
combinations) or unbalanced (RCA)	mono input mode.
inputs.
1-PYLE PPA Amplifier Owner’s Manual

CAUTION! Do not use balanced and unbalanced inputs simultaneously!!

PYLE PPA Amplifier Owner’s Manual – 2

PPA200 specifications

The Radio Shack PPA200 is a versatile portable amplifier designed for a variety of audio applications, including public speaking, teaching, and personal use. This model has garnered attention for its robust performance and user-friendly features, making it an essential tool for professionals and hobbyists alike.

One of the standout characteristics of the PPA200 is its powerful amplification capabilities. With a maximum output of 20 watts, it effectively delivers audio in different environments, ensuring that users can be heard clearly even in larger spaces. The amplifier's compact design also enhances portability, making it easy to transport from one location to another.

In terms of technology, the PPA200 is equipped with both wired and wireless microphone options. This feature allows users to choose their preferred method of audio input. The wireless capability, utilizing advanced UHF technology, provides a reliable connection with minimal interference, ensuring a seamless user experience. Additionally, the amplifier includes an integrated speaker, offering clear and crisp sound quality that adds to its appeal for public speaking or educational scenarios.

Battery life is another critical factor for portable devices, and the PPA200 excels in this area. It features a rechargeable battery that provides several hours of continuous use, allowing users to conduct lengthy sessions without the worry of running out of power. The built-in LED indicators also keep users informed about battery status and system functioning.

The Radio Shack PPA200 is designed with user convenience in mind. The controls are intuitively laid out, making it easy for users to adjust volume levels, select input sources, and configure settings without extensive technical knowledge. Moreover, compatibility with various audio devices, including smartphones, tablets, and laptops, further broadens its usability.

In conclusion, the Radio Shack PPA200 stands out as a reliable, portable amplifier that combines power, flexibility, and ease of use. Its array of features, including powerful amplification, multiple microphone options, long battery life, and straightforward controls, make it an ideal choice for anyone in need of a quality audio solution. Whether for classroom settings, outdoor events, or personal use, the PPA200 delivers performance that meets the demands of various situations.

Radio Shack PPA200 warranty Table of Contents

PPA200 specifications