Samsung HT-F5200/XN, HT-FS5200/XN, HT-F5200/EN, HT-FS5200/EN, HT-F5200/ZF, HT-FS5200/ZF Wi-Fi Direct

5.On the Security type screen that appears, use the ▲▼ buttons to select the network's Security type, and then press the E button. On the next screen, enter your network's security code or pass phrase.

•Enter numbers directly using the number buttons on your remote control.

•Enter letters by selecting a letter with the ▲▼◄► buttons, and then pressing the E button.

When finished, select Done, and then press the E button. The product searches for the network.

6.The Network connection fail screen appears. Use ◄► buttons to select IP Settings, and then press the E button.

7.Select the IP setting field, and then set it to Enter manually.

8.Select a network value to enter (IP Address, for example), and then press E button. Use the number keypad on your remote control to enter the numbers for the value. You can also enter numbers using the ▲▼ buttons. Use the ◄► buttons on the remote control to move from entry field to entry field within a value. When done with one value, press the E button.

9.Press the ▲ or ▼ button to move to another value, and then enter the numbers for that value following the instructions in Step 8.

10.Repeat Steps 8 and 9 until you have filled in all values.

NOTES

You can get the Network values from your Internet provider.

11.When finished, select OK, and then press the E button. The Security Screen appears.

12.On the Security screen, enter your network's Security Code or Pass Phrase. Enter numbers directly using the number buttons on your remote control. Enter letters by selecting a letter with the ▲▼◄► buttons, and then pressing the E button.

13.When finished, select Done at the right of the screen, and then press the E button. The product verifies the network connection and then connects to the network.

14.After the home cinema verifies the network, select OK, and then press the E button.

NOTES

You can also begin the Manual Network setting by going to Settings >Network > Network Status.

❑WPS(PBC)

One of the easiest ways to set up the wireless network connection is using the WPS(PBC) function. If your wireless router has a WPS(PBC) button, follow these steps:

After following Steps 1 to 3 in "Configuring Your Network Connection" on page 23:

1.In the Network Settings screen, change Network type to Wireless. Then, select Connect and press the E button.

The product searches for and then displays a list of the available networks.

2.Scroll the list down, select WPS(PBC), and then press the E button.

3.Press the WPS(PBC) button on your router within two minutes. Your product automatically acquires all the network settings values it needs and connects to your network.

The product connects to the network after the network connection is verified.

4.When it is done, highlight OK, and then press E button.

NOTES

For WPS connection, set your wireless router’s security encryption to AES. Setting to WEP security encryption does not support WPS connection.

Wi-Fi Direct

The Wi-Fi Direct function allows you to connect Wi-Fi Direct devices to the product and each other using a peer-to-peer network, without a wireless router.

NOTES

Some Wi-Fi Direct devices may not support the AllShare function if connected via Wi-Fi Direct. If this is the case, change the network connection method you used to connect the device to the home cinema. Wi-Fi Direct transmissions can interfere with the Bluetooth signal. Before you use the Bluetooth function, we strongly recommend that you turn off the Wi-Fi Direct function on any device in which it is currently on.

1.Turn on the Wi-Fi direct device and activate its Wi-Fi Direct function.

2.In the Home screen, select Settings, and then press the E button.

3.Select Network, and then press the E button.

4.Select Wi-Fi Direct, and then press the E button. The Wi-Fi Direct devices that you can connect appear.

04 Settings

English 25