Troubleshooting
•Do not use benzene, thinner or other flammable sub- stances, or a wet cloth.
•We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen.
2)Maintaining the Flat Panel Display Screen.
Clean with a soft cloth (cotton flannel) smoothly.
•Never use acetone, benzene or thinner.
(They may cause flaws or deformation of the screen surface.)
•The user will be required to pay costs and related expenses for repairing damages caused.
Symptoms and Recommended Actions
Note
A PDP Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the PDP Display to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer.
1.Check if the power cord and the video cables are properly connected to the computer.
2.Check if the computer beeps more than 3 times when booting.
(If it does, request an a service for the main board of the computer.)
3.If you installed a new video card or if you assembled the PC, check if you installed the Adaptor(video).
4.Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz. (Do not exceed 60Hz when using the maximum resolution.)
5.If you have problems in installing the Adaptor (video) driver, boot the computer in Safe Mode, remove the Display Adaptor in the "Control Panel −> System −> Device Admin- istrator" and then reboot the computer to reinstall the Adaptor (video) driver.
Check List
Note
•The following table lists possible problems and their solutions. Before calling for assis- tance, check the information in this section to see if you can remedy any problems for yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
•For more network-related information, refer to the MagicInfo Troubleshooting section.
Problems related to the Installation (PC Mode)
Note
Problems related to the PDP Display installation and their solutions are listed.
Q:The PDP Display screen flickers.
SyncMaster P50F,P50FN,P63F,P63FN
PDP Monitor
Notational Conventions
Power
Notational
Installation
Clean
Others
Page
Page
Page
Unpacking
Package Contents
Sold separately
Your PDP Display Front
Source button Source
RearP50FN
Power
DVI / PC / Hdmi in DVI/PC/HDMI AU
RearP63FN
Using the Anti-Theft Kensington Lock
Power
Remote Control
PIP Swap
Standard → Music → Movie → Speech → Custom
Tom
Standard → Movie → Custom
Mechanical Layout P50FN
PDP Display Head
Installation Vesa Bracket
Dimensions
Components
Wall Bracket Installation
Wall Bracket Assembly
To mount the product on the wall bracket
Page
Wall Bracket Angle Adjustment
Mechanical Layout P63FN
Wall Bracket Assembly
To mount the product on the wall bracket
Wall Bracket Angle Adjustment
Page
Connections
Connecting a Computer Using a Power cord with Earth
Connecting AV Devices
Connecting to Other devices Using a Power cord with Earth
Connecting Using a Hdmi Cable
Connecting to a Camcorder
Connecting a LAN Cable Using a Power cord with Earth
Connecting Using a DVI to Hdmi Cable
Connecting to an Audio System
Connecting a USB device Using a Power cord with Earth
Connections Applicable to the P50FN / P63FN model only
Installation MagicInfo Pro
Using the Software
Page
Page
CPU RAM
System Requirements
Main Screen
Introduction
Port Selection
Power Control
Page
Input Source
PC, BNC, DVI
Image Size
Image Size TV, AV, S-Video, Component, DVIHDCP, HDMI, DTV
Time
PIP Size
PIP
PIP Source
Settings Picture
Settings Picture PC
Settings
Audio
Settings Image Lock
Maintenance Lamp Control
Maintenance Scroll
Maintenance Video Wall
Troubleshooting
Settings Value Display In Multiple Display Mode
Source List
Input Available Modes
PC / DVI
MagicInfo
PC / DVI / Hdmi MagicInfo
Picture PC / DVI / Hdmi / MagicInfo Mode Available Modes
Edit Name
Contrast
MagicBright
Custom
Sharpness
Brightness
Color Tone
Color Control
Green
Red
Blue
Color Temp
Signal Balance
Auto Adjustment
Fine
Position
Offset
Signal Control
→ → Enter → Signal Control Gain
Mode
Picture AV / Hdmi / DVI / TV Mode Available Modes
Size
Dynamic, Standard, Movie, or Custom can be activated
Tint
Color
Digital NR Digital Noise Reduction
Off
Film Mode
Sound Available Modes
Treble
Bass
Balance
Auto Volume
Language
Setup Available Modes
Time
Clock Set
On Timer
Sleep Timer
Safety Lock PIN
Off Timer
Menu Transparency
High Medium Low Opaque
Hdmi Black Level
Energy Saving
Video Wall
Normal Low
Horizontal
Format
Full
Natural
Screen Divider
Safety Screen
Vertical
Vertical Line
Pixel Shift
Horizontal Dot
Timer
Scroll Bar Eraser All White Pattern
Period
Bar
Scroll
Eraser
All White
Resolution Select → , → Enter
Resolution Select
Pattern
Off 1024 X
Side Gray
Power On Adjustment
Reset
Color Reset
Image Reset
ID Setup
Multi Control Available Modes
ID Input
MagicInfo Available Modes
Select Magicinfo in the Source List menu
Magicinfo
Page
Photo
Slide Show
Auto
Original
Rotation
Interval
Close
Zoom
Play
Music
Movie
Office / Html
Full Size
Schedule View
Setup
Internet
Connection
TCP/IP
File
Password
Rotation Sets the picture orientation
Play Option
Maintenance and Cleaning
Self-Test Feature Check
Check List
Symptoms and Recommended Actions
Problems related to the Installation PC Mode
Not Optimum Mode message
Problems related to the Screen
Check Signal Cable message
Problems related to the Remote Control
Problems related to Audio
Problems related to MagicInfo
Page
General
Signal Cable
Power Supply
Dimensions W x H x D / Weight
Vesa Mounting Interface
Ethernet Application
MagicInfo Client
MagicInfo Pro Server Requirement
PowerSaver When used as a Network PDP Display
PowerSaver
PowerSaver When used as a normal PDP Display
Preset Timing Modes
VESA, 800 x 37.879 60.317 40.000
Product Information Image Retention Free
For Better Display
Power Off, Screen Saver, or Power Save Mode
Select method
Apply the Screen Erasing function on Product
Page
North America
Contact Samsung Worldwide
Latin America
Europe
CIS
Terms
Authority
Correct Disposal
Appendix