Samsung MMS8RH/ELS Connecting your System to the Power Supply, Inserting Remote Control Batteries

Page 7

Where to Install Your

Micro Component System

To take full advantage of your new micro component system, follow these installation instructions before connecting the unit.

Install the system on a flat, stable surface.

Never place this unit on carpeting.

Never place this unit in an outdoor area.

Maintain an open space of approximately 6 inches (15 cm) on the sides and rear of the system, for ventilation purposes.

Make sure that you have enough room to open the compact disc compartment easily.

Place the loudspeakers at a reasonable distance on either side of the system to ensure good stereo sound.

Direct the loudspeakers towards the listening area.

For optimum performance, make sure that both speakers are placed at an equal distance above the floor.

		Volume
DEMO/
DIMMER	TUNER	CD
	Band
	TAPE	AUX
REV.MODE
		SRS WOW
CD SYNC.	TUNING	STOP
	TUNING	STOP
	MODE
		OPEN/CLOSE
	/DOWN	UP/

PHONES

Connecting your System to the Power Supply

The main lead must be plugged into an appropriate socket.

Before plugging your system into a main socket, you must check the voltage.

1		Plug the main lead (marked AC Cord on the rear of the system) into
		an appropriate socket.
2		Press the (			) button to switch your micro component system on.

Inserting Remote Control Batteries

GB

Insert or replace remote control batteries when you:

Purchase the micro component system

Find that the remote control is no longer operating correctly

When replacing the batteries, use a new set of batteries and never mix alkaline and manganese batteries.

1	Place your thumb on the position marked		on the battery
	compartment cover (rear of the remote control) and push the cover in
	the direction of the arrow.
2	Insert two AAA, LR03 or equivalent batteries, taking care to respect
	the polarities:
	+ on the battery against + in the battery compartment
	– on the battery against – in the battery compartment
3	Replace the cover by sliding it back until it clicks into position.

7

Image 7

Contents Micro Component Audio System Class 1 Laser Product Safety WarningsContents Front Panel View Mute Remote ControlRear Panel View Insert or replace remote control batteries when you Connecting your System to the Power SupplyWhere to Install Your Micro Component System Inserting Remote Control BatteriesRight Speaker Left Speaker Connecting to an External Source Speaker ConnectionConnect To the connector marked CD Digital Out JackAM aerial for long and medium waves can be Connecting the AM MW/LW AerialConnecting the FM Aerial How to connect a Coaxial Type aerialPress PROGRAM/SET Setting the ClockDemo Function Dimmer FunctionSelecting a Track Listening to a Compact DiscSearching for a Specific Music Passage on a CD To repeat Function to skip through 10 tracks at a timeRepeating One or All Tracks on the Compact Discs Repeat A↔ B FunctionChecking or Changing Programmed Tracks Programming the Order of PlaybackYou can improve the quality of radio reception by Selecting a Stored StationImproving Radio Reception To listen to PressDescription on RDS function About RDS broadcasting About RDS Display functionAppears automatically on the display RDS function is available only in FM broadcastingAbout PTY-SEARCH PTYProgram Type indication and PTY-SEARCH functionFM and frequency appear on the display Listening to a Cassette Selecting the Cassette Playback ModeYou can record a radio program of your choice Recording a Compact DiscRecording a Radio Program REC/PAUSE buttonIf you select You must also Timer FunctionCanceling the Timer Press Timer ON/OFFSRS WOW Function EQ/S.BASS FunctionMute Function Connecting HeadphonesSetting the System to Switch off Automatically Mute again or the Volume buttonsPress Push Eject Safety Precautions Cleaning Your Micro Component SystemBefore Contacting the After-Sales Service Precautions When Using Compact DiscsPrecautions When Using Audio Cassettes Compact Disc Player Technical SpecificationsElectronics