❙CAMERA ID
In the CAMERA ID menu, you may designate the CAMERA ID to be displayed in the monitor connected to a camera. Set the CAMERA ID menu to ON... and press [ENTER] and the CAMERA ID setup submenu will appear. The CAMERA ID may be created by up to 20 digits by using alphabets, numbers, and some special texts served by the submenu
✔WDR
WDR(Wide Dynamic Range) enlarges the advantage of a screen, mostly effective photographing both indoor and outdoor subjects simultaneously. In short, both subjects can be distinctly revived. Select WDR... and press [ENTER] to set up WDR LEVEL and FLICKERLESS.
screen. You may locate the designated CAMERA ID on your own by using the LOCATION... submenu.
CAMERA ID | OFF |
IRIS | WDR... |
SHUTTER | OFF |
AGC | LOW |
WHITE BAL | ATW1 |
(IRIS/WDR)
E
CAMERA ID | ON... |
IRIS | ALC... |
SHUTTER | OFF |
AGC | LOW |
WHITE BAL | ATW1 |
FOCUS MODE | AF |
MOTION DET | OFF |
COLOR/BW | COLOR |
PRIVACY | OFF |
SPECIAL | ... |
PRESET | ... |
Press the
ENTER button.
(CAMERA ID)
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9
. ; ! - +* () /
SP❿❿➛➛SP
LOCATION...
RET
FOCUS MODE | AF |
MOTION DET | OFF |
COLOR/BW | COLOR |
PRIVACY | OFF |
SPECIAL | ... |
PRESET | ... |
EXIT | QUIT |
Press the
ENTER button.
LEVEL1 | L | I | H |
LEVEL2 | L | I | H |
FLICKERLESS | OFF |
|
|
RET |
|
|
|
EXIT | QUIT |
......................
- | LEVEL 1 | : Controls the shutter speed while WDR |
| operates. |
|
- | LEVEL 2 | : Controls the whole brightness while WDR |
❙IRIS
✔ALC
Select ALC... from the IRIS menu and press [ENTER] and the BLC(Back Light Compensation) setup submenu will appear. If you use a general camera to photograph a subject under backlight or bright illumination, the subject will be shown dark on the monitor due to the backlight. BLC(Back Light Compensation) is used to prevent such a backlight problem to secure distinct images under bright illumination. Use ➞ and ➞ in the LEVEL menu to control the video output level(brightness).
operates. |
- FLIKERLESS : This is for preventing flicker on the screen |
when NTSC system is used in 50HZ power supply region |
and PAL system is used in 60HZ power supply region. |
That is to prevent shaking on the screen resulted from |
the discordance of the vertical sync frequency and the |
flicker frequency of the illumination. While this menu is |
ON, the electronic shutter is fixed to 1/100sec (NTSC) or |
1/120 sec (PAL). |
| CAMERA ID | OFF |
| |
|
| |||
| IRIS |
| ALC... |
|
| SHUTTER | OFF |
| |
| AGC | LOW |
| |
| WHITE BAL | ATW1 |
| |
| AUTO FOCUS | AF |
| |
| MOTION DET | OFF |
| |
| COLOR/BW | COLOR |
| |
| PRIVACY | OFF |
| |
| SPECIAL | ... |
| |
| PRESET | ... |
| |
| EXIT | QUIT |
| |
|
|
|
|
|
Press the
ENTER button.
(IRIS/ALC)
BLC | ON |
LEVEL (0) | |
RET |
|
17 | 18 |