Lightolier 9279 instruction sheet Instructions for Attaching Suspended, Louver, Lytespan Track

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE	INSTRUCTION SHEET NO.
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.	IS: 9279
To assure full compliance with local codes and regulations, check with your local electrical inspector
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.	A0101	Page 2 of 4

INSTRUCTIONS FOR ATTACHING SUSPENDED PowerWashTM T5 POWER STEM TO A

LYTESPAN® TRACK SYSTEM. FOR USE WITH LYTESPAN TRACK SYSTEMS ONLY.

TRACK POWER

INSTRUCTION SHEET NO.

IS: 9279

A0101 Page 3 of 4

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE

This luminaire is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector

before installation. To prevent electric shock, turn off electricity at fuse box before proceeding. Retain these instructions for maintenance reference.

INSTRUCTIONS FOR INSTALLING A PowerWashTM T5 LOUVER

NOTE: Not for use with ProSpec® Track.STEM LEVER

INSTRUCTIONS FOR ATTACHING SUSPENDED

PowerWash T5 POWER STEM TO SINGLE CIRCUIT

INSTRUCTIONS FOR INSTALLING A PowerWash T5

LOUVER:

TOP

SPRINGS

Fig. 17

LYTESPAN TRACK

BEAD

1. Turn off power to TRACK.

2. Insert POWER STEM into TRACK. The POWER STEM LEVER must be on the same side as the track BEAD. See Fig. 11.

3. Rotate POWER STEM 90fl clockwise using POWERPOWER STEM LEVER. POWER STEM LEVER should be parallel

1.	Turn off power to TRACK.
2.	First insert BOTTOM SPRINGS on the LOUVER into the
BOTTOM GROOVE in the luminaire (see Fig. 17 & 18).
3.	While pushing down TOP SPRING TABS, rotate LOUVER
toward the TOP GROOVE in the luminaire until it hits the
FRONT STEP on the luminaire. Release the TOP SPRING TABS

BOTTOM SPRINGS

with TRACK. See Fig. 12.

STEM

into the TOP GROOVE (see Fig. 17, 19, & 20).

4.To remove: rotate POWER STEM 90fl counterclockwise using POWER STEM LEVER.

4. To remove, push down the TOP SPRING TABS and rotate

away from the luminaire (see Fig. 19).

SPRING TAB

INSTRUCTIONS FOR CONVERTING SUSPENDED PowerWash T5 POWER STEM ATTACHMENT FITTING TO OPERATE ON 2 CIRCUIT ADVENT LYTESPAN TRACK:

	Fig. 11	Fig. 12
MOVABLE	BLACK
BRASS	SPACER
CONTACT

NOTE: Ensure that all four LOUVER SPRINGS are fully engaged for safe operation (see Fig. 20).

NOTE: Luminaire may be used without LOUVER if desired.

Fig. 18

BOTTOM

SPRINGS

PLUG

TOP

BOTTOM GROOVE

NOTE: To insure proper operation of PowerWash T5 suspension on Two Circuit Lytespan Track, the BLACK SPACER (provided) must be used at all times. The BLACK SPACER is not used when operating PowerWash T5 on Single Circuit Track.

LOWER CIRCUIT, Fig. 13 & 16:

Illustrates BRASS CONTACT in low position with BLACK SPACER in place for lower circuit.

UPPER CIRCUIT, Fig. 14, 15, & 16:

To convert power stem attachment fitting for upper circuit,

raise BRASS CONTACT to high position (as indicated by dotted line) by pulling CONTACT as high as stop permits and slipping on BLACK SPACER as shown in Fig. 14 & 15.

Do not try to move stationary silver contact.

U.S. PAT. PENDING

ASSEMBLY
MOVABLE	STATIONARY
BRASS	CONTACT
CONTACT	(Neutral)

Fig. 13

PLUG

ASSEMBLY

MOVABLE	BLACK	BLACK
		SPACER
BRASS	SPACER
CONTACT

Fig. 14

PLUG

ASSEMBLY

UPPER

CIRCUIT

Fig. 15	LOWER	NEUTRAL
	CIRCUIT

Fig. 16

LIGHTOLIER a GENLYTE THOMAS company.

631 Airport Road, Fall River, MA 02720

U.S. PAT. PENDING

GROOVE

FRONT STEP

LOUVER

Fig. 19

Fig. 20

LIGHTOLIER a GENLYTE THOMAS company.

631 Airport Road, Fall River, MA 02720