Samsung BD-F5500/ZF Dynamic Range Control, PCM Downsampling, Downmixing Mode, Network Settings

✎✎ NOTES

Dynamic Range Control Wired Network Settings

8. When the Network Test is complete,

`` Be sure to select the correct Digital Output or you will hear no sound or just loud noise.

`` If the HDMI device (AV receiver, TV) is not compatible with compressed formats (Dolby Digital, DTS), the audio signal outputs as PCM.

`` Regular DVDs do not have BONUSVIEW audio and Navigation Sound Effects.

`` Some Blu-ray Discs do not have BONUSVIEW audio and Navigation Sound Effects.

`` If you play MPEG audio soundtracks, the audio signal outputs as PCM regardless of your Digital Output selections (PCM or Bitstream).

`` If your TV is not compatible with compressed multi-channel formats (Dolby Digital, DTS), the player may output PCM 2ch downmixed audio even though you selected Bitstream (either Re- encoded or Unprocessed) in the setup menu.

`` If your TV is not compatible with PCM sampling rates over 48kHz, the player may output 48kHz downsampled PCM audio even though you set PCM Downsampling to Off.

PCM Downsampling

Lets you choose to have 96KHz PCM signals downsampled to 48KHz before they are outputted to an amplifier. Choose only if your amplifier or receiver is not compatible with a 96KHz signal.

Lets you apply dynamic range control to Dolby Digital, Dolby Digital Plus, and Dolby True HD audio.

•Auto : Automatically controls the dynamic range of Dolby TrueHD audio, based

on information in the Dolby TrueHD soundtrack.

Also turns dynamic range control on for Dolby Digital and Dolby Digital Plus.

•Off : Leaves the dynamic range uncompressed, letting you hear the original sound.

•On : Turns dynamic range control on for all three Dolby formats. Quieter sounds are made louder and the volume of loud sounds is reduced.

Downmixing Mode

Lets you select the multi-channel downmix method that is compatible with your stereo system. You can choose to have the player downmix to normal stereo or to surround compatible stereo.

Network Settings

Please contact your ISP to find out if your IP address is static or dynamic. If it is dynamic - and most are - we recommend using the Auto procedure for network setup. This is easiest and will work in the majority of cases. If it is static, you must use the manual set up procedure.

Network setup directions start below. ✎✎ NOTES

`` This unit can only be connected to a Network via a wired connection.

1.In the Home menu, press the ◄► buttons to select Settings, and then press the v button.

2.Press the ▲▼ buttons to select Network, and then press the v button.

3.Press the ▲▼ buttons to select Wired Network Settings, and then press the v button. The Wired Network Settings screen appears.

Settings

Display		Wired Network Settings
Audio	Internet Protocol Setup : Auto						\
Network		IP Address	:	0	0	0	0
System		Subnet Mask	:	0	0	0	0
Language Gateway			:	0	0	0	0
SecurityDNS			: Auto		0	0	0
General		DNS Server	:	0
Support			> Move " Select ' Return

4.In the Internet Protocol Setup field, select Auto if it is not selected. (Press v button and select Auto, and then press v.)

5.The Auto Function acquires and fills in the values for IP Address, Subnet Mask, etc., automatically.

✎NOTES✎

`` This process can take up to five minutes.

6.After the Network Function has acquired the network values, press the RETURN button.

7.Select Network Test, and then press v to ensure the player has connected to your network.

press the RETURN button twice to

return to the Main Menu.

9. If the Network Function does not acquire

the network values, go to the directions

for Manual Setup.

Manual Network Setup

Before you start manual network setup, you need the network setting values.

To get the network setting values, contact your ISP (Internet Service Provider) or your network administrator.

To enter the Network Settings into your player, follow these steps:

1.In the Home menu, press the ◄► buttons to select Settings, and then press the v button.

2.Press the ▲▼ buttons to select Network, and then press the v button.

3.Press the ▲▼ buttons to select Wired Network Settings, and then press the v button. The Wired Network Settings screen appears.

4.Select the Internet Protocol Setup field, and then press the v button.

5.Press the ▲▼ buttons to select Manual, and then press the v button.

6.Press the ▼ button to go to the first entry field (IP Address).

7.Use the number buttons on your remote to enter numbers.

13