Lightolier IS:F302IC instruction sheet 302ESIC, For NEW Ceiling Mounting BAR, Mounting Frame

INSTRUCTION SHEET	ISF:302IC
	12-01/Rev-02

INSTALLATION INSTRUCTIONS FOR MOUNTING FRAME

FOR INSULATED CEILING

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with National Electrical Code or Canadian Electrical

Code (as applicable) and local regulations. To ensure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

302ESIC

302MRIC / 402MRIC

WOOD JOIST		VAPOUR BARRIER
		EXTENDER
VAPOUR
BARRIER EXTENDER
FIXTURE			SILICONE
			SEALER
			OR OTHER
VAPOUR BARRIER	FIG.1	VAPOUR BARRIER	FIG.2

WITH VAPOUR BARRIER COVER: NºVBE300 (Order separately)

1.	Select a location for the fixture.
2.	Fasten the edge of the vapour barrier cover under the
	wood joist. (Fig.1)
3.	Install the fixture (see step A, B and C).
4.	Install the ceiling vapour barrier. (Fig.1)	MOUNTING
	Note: Seal the edges of the vapour barrier cover and the		BAR
	vapour barrier. (Fig.2)
FOR NEW CEILING:
A. MOUNTING BAR:
	Note-1: The mounting bars are extensible from 12½" to 29" max.
	Note-2: For off-centre installation, use 20" expandable mounting bars
	(Nº1964, order separately).
1.	Insert the mounting bars into the proper openings on the short side or the
	long side of the mounting frame. (Fig.4)

BUILT-IN
NAILER		MOUNTING
	WOOD	FRAME
	JOIST

LOCKING

T A B S

FIG.3	MOUNTING	FIG.4
	BAR
		F L E X I B L E
LOCKING		WIRE
CLIP		"PRY-OUT"
		PLUG

2.	Align the mounting bar with the bottom edge of the joist. (Fig.3)
3.	Push in the built-in nailer. (Fig.3)
	MOUNTING

BAR

MOUNTING FRAME

JUNCTION B O X

B. MOUNTING FRAME:

1.Install the locking clip. (Fig.5)

Note-1: The locking clip is also available separately (Nº0098, order separately).

Note-2: To lock more securely into place fold the locking tabs. (Fig.4)

	WIRE
	CONNECTOR
FIG.5	FIG.6

C. WIRE-IN:

1.Remove the appropriate "Pry-out plug".

2.Insert the supply lead into the junction box:

a)If using FLEXIBLE CONDUIT: Use a BX connector (not provided).

b)If using FLEX WIRE: Insert under the wire connector. (Fig.6)

3.Connect the ground lead. (Fig.7,8)

4.Connect the white leads (NEUTRAL) together, and the black leads (120V) together. (Fig.7.8)

D. CEILING:

1. Cut a hole in the ceiling (3-3/4” for Model 302 or 4-3/4” for

Model 402), using the mounting frame as a template (if applicable).

THERMAL

PROTECTOR

LAMP

INPUT(120V)

		NEUTRAL (white)
BALCK	WHITE
		GROUND

LOW VOLTAGE JUNCTION TANSFORMER

BOX

		INPUT(120V)
	BLACK WHITE	NEUTRAL (white)
THERMAL		GROUND
PROTECTOR

LAMP

JUNCTION

BOX

	(Fig.9)
2.	Use the screws to adjust the housing height. Note: Ensure
	that the housing is level with the ceiling. (Fig.10)
3.	Tighten the screws when completed. (Fig.10)
	CAUTION: The lampholder must not be used for temporary lighting,
	a protective glass is required for the lamp.

E.TRIM:

Install the trim using the appropriate sheet.

F. TRANSFORMER / REPLACEMENT:

Note: Before performing maintenance on the transformer, make sure that the electrical supply to the fixture is turned off.

1.Remove the housing and the two screws located inside. (Fig.10)

2.Push down on the spring tab and release the plate. (Fig.11, 12)

3.Remove the plate from the ceiling, disconnect the wiring , and change the transformer. (Fig.12)

4.Complete the connections following the wiring diagram (fig.7). Reinstall the plate onto the spring. (Fig.12)

5.Replace the housing into position. (Fig.10)

FIG.7	FIG.8
(MR)	(ES)

HOUSING

SCREWS

FIG.9 FIG.10

PLATE

TAB	FIG.11	FIG.12
		SPRING