Lightolier IS:CCLPS602P instruction sheet CCLPS602P Specifications

	Architectural Decorative  IS:CCLPS602P
Page 4 of 4	Instruction Sheet for Assembly and Installation

Group	How Luminaires Are Addressed
Address
-1	All luminaires are addressed sequentially, starting with the Base
	Address. If you have 20 luminaires with a Base Address of 1, they are
	addressed as follows:
	Light #:	1	2	3	4	5	6	7		8 ... 18 19				20
	Address:	20 19 18 17 16 15 14 13 ...										3	2	1
-2	Every two luminaires are assigned the same address. For example, if
	you have 20 luminaires with a Base Address of 1, they are addressed
	as follows:
	Light #:	1	2	3	4	5	6	7	8	...	18	19	20
	Address:	10	10	9	9	8	8	7	7	...	2	1		1
-3	Every three luminaires are assigned the same address. For example,
	if you have 20 luminaires with a Base Address of 1, they are ad-
	dressed as follows:
	Light #:	1	2	3	4	5	6	7	8	...	18	19	20
	Address:	7	7	6	6	6	5	5	5	...	1	1		1
-4 to -20	...

Note: It is recommended that you set your group number to a number that evenly divides the number of luminaires connected to Output 1 and you balance the number of luminaires on each output. Otherwise, you may have a smaller amount of luminaires at the end of each output port that would receive the next address.

5.To exit Configuration mode, press both buttons simultaneously. The base address for CCLPS602P will appear on the display.

CCLPS602P Specifications

Power Input	100-240VAC, 50Hz–60Hz, 1.1-0.4A
Power Output	24VDC (62W Max.)
Heat Dissipation	22% of total power input at maximum load
Ambient Operating Temp	14°F to 122°F (-10°C to 50°C)
Housing	8.8” (22.4 cm) X 4.0” (10.2 cm) X
	2.0” (5.1 cm)
	Weight: 2.0 lbs (907 g)
Connectors	Data: RJ45 input and output connectors
	Power: 4-pin output connectors, IEC power con-
	nector (Supplied with C13 IEC plug, grounded US
	outlet plug. UL/CSA rated 18 AWG 3/C ST 90°C
	Rated.)
Data Input Interface	Lightolier Lytemode DMX, color rotary dial or
	DMX 512 compatible controllers.
Data Output Interface	24V
Classification	Class 2
Listings	UL/cUL, CE, PSE
Max. # of Luminaires	12": 20; 6": 36

Fig. 9

Examples of Sequential and Reverse Addressing

Note: Reverse addressing only reverses the addresses on Output 1 of the CCLPS602P.

Group Address	10	9	2	1	1	2	9	20
Set to “1”
Group Address	1	2	9	0	1	2	9	20
Set to “-1”

Example 1:

When using a Rainbow Wash with sequential addressing (group address set to 1), the luminaire flows from the center

(the first luminaire on Output 1) to the last luminaire in Output 1, and then back to the first luminaire on Output 2.

When using a Rainbow Wash with reverse addressing (group address set to -1), the luminaire flows from left to

right across all fixtures. The luminaire goes from the last fixture on Ouput 1 to the first fixture on Output 1, and then to the

first fixture on Output 2 to the last fixture on Output 2.

Group Address	1	2	20
Set to “1”
Group Address	1	2	20
Set to “1”

OUT 1	OUT 2
ENET IN	DMX IN	DMX OUT

CCLPS602P

(Center Feed Installation)

Base Address = 1

40	22	2	Group Address
			Set to “-1”
2	39	40	Group Address
			Set to “-1”

OUT 1	OUT 2
ENET IN	DMX IN	DMX OUT

CCLPS602P DMX/Ethernet

(Base Address = 1)

Example 2:

Reverse addressing allows you to have a continuous Rainbow Wash when you have an installation fed by more than one power supply. When using sequential addressing on both power supplies, the luminaire flows from the first luminaire on Output 1 of the first power supply to the last luminaire on Output 1 (left to right), and then it flows from the first luminaire on Output 1 of the second power supply to the last luminaire on Output 1 (right to left).

Using reverse addressing on the second power supply allows you to set up the flow from left to right across all fixtures. With this setup,

the luminaire flows from the first luminaire on Output 1 of the first power supply to the last luminaire on Output 1, and from the last luminaire on Output 1 of the second power supply to the first luminaire on Output 1.

OUT 1	OUT 2
ENET IN	DMX IN	DMX OUT

CCLPS602P DMX/Ethernet

(Base Address = 21)

631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710 We reserve the right to change details of design, materials and finish. www.lightolier.com © 2008 Philips Group • A0908

Lightolier is a Philips group brand