USE and Maintenance

to handle.

In the case of assembly of the appliance in the suction version prepare the hole for evacuation of the air.

•We recommend the use of an air exhaust pipe with a diameter of 150. If a pipe with a smaller diameter is used, the efﬁ ciency of the product may be reduced and its operation may become noisier

•FIXING TO THE WALL

Drill the holes A respecting the distances indicated (Fig.2). Fix the appliance to the wall and align it in horizontal position to the wall units. When the appliance has been adjusted, definitely fix the hood using the screws A (Fig.4). For the various installations use screws and screw anchors suited to the type of wall (e.g. reinforced concrete, plasterboard, etc.). If the screws and screw anchors are provided with the product, check that they are suitable for the type of wall on which the hood is to be ﬁ xed.

•FIXING THE DECORATIVE TELESCOPIC FLUE Take care not to scratch the duct; wear gloves when removing the protective ﬁ lm. (Fig. 7)

Arrange the electrical power supply within the dimensions of the decorative ﬂ ue. If your appliance is to be installed in the ducting version or in the version with external motor, prepare the air exhaust opening. Adjust the width of the support bracket of the upper ﬂ ue (Fig.3). Then ﬁ x it to the ceiling using the screws A (Fig.3) in such a way that it is in line with your hood and respecting the distance from the ceiling indicated in Fig.2. Connect the ﬂ ange C to the air exhaust hole using a connection pipe (Fig.4).

Insert the upper ﬂ ue into the lower ﬂ ue. Fix the lower ﬂ ue to the hood using the screws B provided (Fig.4), extract the upper ﬂ ue up to the bracket and ﬁ x it with the screws B (Fig.3).

To transform the hood from a ducting version into a ﬁltering version, ask your dealer for the charcoal ﬁ lters and follow the installation instructions.

•FILTERING VERSION

Install the hood and the two ﬂ ues as described in the paragraph for installation of the hood in ducting version. To assemble the ﬁ ltering ﬂ ue refer to the instructions contained in the kit. If the kit is not provided, order it from your dealer as accessory.The charcoal ﬁlters must be ﬁtted in the ducting unit located inside the hood (Fig.6).

•It is recommended to operate the appliance prior to cooking.

It is recommended to leave the appliance in operation for 15 minutes after cooking is terminated in order to completely eliminate cooking vapours and odours.

The proper function of the cooker hood is conditioned by the regularity of the maintenance operations, in particular, the active carbon ﬁ lter.

•The anti-grease ﬁ lters capture the grease particles suspended in the air, and are therefore subject to clogging according to the frequency of the use of the appliance.

In order to prevent ﬁ re hazard, it is recommendable to

clean the ﬁ lter at a maximum of 2 months by carrying out the following instructions:

-Remove the ﬁ lters from the cooker hood and wash them in a solution of water and neutral liquid detergent, leaving to soak.

-Rinse thoroughly with warm water and leave to dry.

-The ﬁ lters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several washes. This is not cause for customer complaint nor replacement of panels.

•The active carbon ﬁ lters purify the air that is replaced in the environment. The ﬁ lters are not washable nor re-useable and must be replaced at maximum every four months. The saturation of the active carbon ﬁ lter depends on the frequency of use of the appliance, by the type of cooking and the regularity of cleaning the anti-grease ﬁ lters.

•Clean the fan and other surfaces of the cooker hood regularly using a cloth moistened with denatured alcohol or non abrasive liquid detergent.

•The illumination installation is designed for use during cooking and not for prolonged general illumination of the environment. Prolonged use of the illumination installation notably reduces the duration of the bulb.

•Replacing halogen light bulbs (Fig. 8).

To replace the halogen light bulbs B, remove the glasspane C using a lever action on the relevant cracks.Replace the bulbs with new ones of the same type.

Caution: do not touch the light bulb with bare hands.

•COMMANDS: (Fig.9) MECHANICAL_the key symbols are explained below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

G = MOTOR WORKING indicator

T H E M A N U FA C T U R E R D E C L I N E S A L L RESPONSIBILITY FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE WARNINGS.

- 19 -