Lightolier XP2GVA2FT120SB Photometry, Ordering Information, Options/Accessories, Specifications

	Lens Recessed XP/XA Series
Page 2 of 2	Static, 2' x 2', Recessed Fluorescent, Flat Steel Lens Frame (XP)
	Regressed Aluminum Lens Frame (XA), 2 Lamp TT5

Photometry Model No. XP2GVA2FT120SB

G03129

XP2GVA2FT120SB

THIS REPORT IS BASED ON PUBLISHED INDUSTRY PROCEDURES • FIELD PERFORMANCE MAY VARY FROM LABORATORY PERFORMANCE.

LER = FL - 74.3			IW - 58		BF - 0.87
Comparative yearly lighting energy cost per 1000 lumens = $3.24
	coefficients of utilization — zonal cavity method							(effective floor cavity reflectance 0.20)
		RF		20					20					20
		RC		80					50					30
		RW	70	50		30		50	30	10		50		30	10
		1	92	85		89		83	81	78		80		78	76
	ratio	2	85	78		73		74	70	66		71		68	65
		3	78	69		63		66	61	56		63		59	55
	cavity	4	72	62		55		59	53	49		57		52	48
		5	66	56		49		53	47	43		52		46	42
	room	6	61	51		43		48	42	38		47		42	37
		7	57	46		39		44	38	34		43		37	33
		8	53	42		35		40	34	30		39		34	30
		9	50	39		32		37	31	27		36		31	27
		10	47	36		29		35	29	25		34		29	25
	visual comfort probability			(rated lumens per lamp 2850.)
		room size				ceiling height						ceiling height
	W		L		8.5	10.0	13.0	16.0			8.5	10.0	13.0		16.0
20			20		53	57	65	74			51	55	62		70
20			30		46	50	54	62			43	47	52		59
20			40		43	45	49	54			39	42	46		51
	20		60		40	42	45	49			35	38	41		45
30			20		55	58	64	71			53	57	62		69
30			30		47	50	54	60			45	48	52		57
30			40		43	45	48	52			39	42	46		50
30			60		39	42	43	47			35	38	40		44
	30		80	lengthwise	38	40	41	44		crosswise	34	36	37		40
40			40		44	45	49	52			41	44	47		50
40			20		56	60	65	71			55	59	64		69
40			30	luminaries	49	52	55	59		luminaries	46	50	53		57
40			60		40	42	44	47			36	39	40		44
40			80		38	40	40	43			34	36	37		40
	40		100		38	39	39	41			34	35	35		38
60			30		49	53	55	60			48	52	54		58
60			40		45	47	49	52			42	45	48		51
60			60		40	43	44	47			37	40	41		44
60			80		38	40	40	43			35	37	37		40
	60		100		38	39	38	41			34	35	35		37
100			40		47	50	51	55			46	48	50		54
100			60		43	45	45	49			41	43	43		47
100			80		41	42	42	44			38	39	39		42
	100		100		39	40	39	42			36	37	36		38

Ordering Information

Explanation of Catalog Number. Example: XP2GVA2FT120SBGLR

			2			G			VA
XP = Recessed		Fixture		Width	Ceiling		Type:	Lens Shielding
	Fluorescent				G = Grid (lay-in)				Type:
	with Flat Steel					T-bar		VA = Virgin Acrylic
	Lens Frame								(standard) see
XA = Recessed									options and
	Fluorescent								consult factory
	with Regressed
	Aluminum
	Lens Frame

2

Lamp

Quantity: (By others) 2 = 2 Lamp

						-
	FT
Lamp Fixture Length:		Voltage:						Options:
FT = Twin Tube (T5)		120, 277 or						Lamps
	(Nominal 24")	UNV=120-277						Flex
								Fuse
				Ballast	Type:			(Consult your
					<20THD <10THD		representative)
			1-2 Lamp Elec. (TT5)		SB*	IB*
			LOL TT5 Dimming		PB	–
			*Instant Start Standard
			Other dimming options. Consult factory.

Options/Accessories

Special Lens: Substitute VY for .125" nominal pattern 12 with 7.8 oz. average weight per square foot. Substitute VI for .125" normal pattern 12 with 6.8 oz. average weight per square foot.

Access Plates: Top wiring access plate is shipped with fixture as standard. When access plates are required in advance for wiring convenience, specify separately. Order Catalog Number: ACP CSP. Electrical Wiring Options: Consult factory.

Fusing: Internal fast-blow fusing. Suffix: GLR.

Internal slow-blow fusing. Suffix: GMF.

Radio Interference Filter: 120 or 277 volt, 50 or 60 Hz. One per fixture: Suffix: R. One per

ballast: Suffix: B.

Drywall Kit: G type fixtures for drywall or plaster ceilings. Order Catalog Number: FK92X2.

Specifications

Performance: In an installation of 2 lamps 40 W luminaires in a room cavity ratio of 1, with reflectance of 80% ceiling, 50% walls, 20% floor, the C.U. shall not be less than .89. To reduce glare the VCP shall not be less than 37 either lengthwise or crosswise (at 100 fc level) and the average brightness at 65 shall not exceed 3956 footlamberts. To control veil- ing reflections, luminaire output in the 30°-90° zone shall be not less than 68%.

Specifications (continued)

Materials: Chassis parts are die-formed code gauge cold rolled steel. Lens frames— (XP) flat full-size steel frame, (XA) regressed full-size aluminum frame.

Finish: Chassis exterior—white baked polyester enamel. Cavity—white baked polyester enamel minimum 86% reflectance. Phosphate undercoating.

Lens: Extruded virgin acrylic 3/16" square based female cones, running 45° to the panel edge. .095" nominal thickness (similar to pattern 12).

Electrical: Thermally protected class “P” ballast C.B.M. approved, non PCB. If K.O. is with- in 3" of ballast, use wire suitable for at least 90°.

Labels: I.B.E.W./UL and ULc Listed.

This product may have a mercury containing lamp. Manage in accord with Disposal Laws. See: www.lamprecycle.org

Job Information Type:

For Factory Technical Information: (978) 657-7600 • Fax (978) 658-0595

631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710 We reserve the right to change details of design, materials and finish.

www.lightolier.com © 2008 a Philips Group Section 1A/Folio F60-55 Rev. A

Lightolier is a Philips group brand