Lightolier VRA1G8LS232 dimensions Options & Accessories, Specifications

SECTION 2/Folio G05-36A REV. A

	VR PARABOLIC VRA1G8LS232
Page 2 of 2	1'x4' RECESSED FLUORESCENT, 3" DEEP, 8 CELL (1 ROW) PARABOLIC LOUVER
	STATIC OR AIR SUPPLY/RETURN, 2 LAMP T8 OR T12

PHOTOMETRY MODEL NO. VRA1G8LS232120SO

VRA1G8LS232SO

LER = FP - 57.0				IW - 59.1		BF - 0.88
Comparative yearly lighting energy cost per 1000 lumens = $4.21
	coefficients of utilization — zonal cavity method
		RF		20			20			20
		RC		80			50			30
		RW	70	50	30	50	30	10	50	30	10
		1	75	72	70	68	67	65	66	64	63
	ratio	2	70	65	62	62	59	57	60	58	56
		3	65	59	55	56	53	50	54	52	49
	cavity	4	60	53	48	51	47	44	49	46	43
		5	55	47	42	45	41	38	44	40	37
	room	6	51	43	37	41	36	33	40	36	33
		7	47	38	33	37	32	29	36	32	29
		8	43	34	29	33	28	25	32	28	25
		9	39	31	25	29	25	21	29	24	21
		10	36	28	22	27	22	19	26	22	19

visual comfort probability

room size				ceiling height					ceiling height
W	L		8.5	10.0	13.0	16.0		8.5	10.0	13.0	16.0
20	20		80	72	68	74		74	64	60	67
20	30		82	76	72	69		78	69	62	61
20	40		84	78	76	73		80	72	66	63
20	60		85	79	78	75		80	75	70	66
30	20		84	76	68	71		78	70	62	66
30	30		85	79	72	67		81	74	64	60
30	40		86	81	75	70		83	76	68	62
30	60		87	82	77	73		83	79	71	66
30	80	lengthwise	87	83	79	75	crosswise	83	79	74	68
40	40		87	83	78	70		85	79	72	63
40	20		85	79	71	71		80	74	67	67
40	30	luminaries	86	81	75	67	luminaries	83	77	68	62
40	60		88	84	79	73		85	81	74	67
40	80		88	84	81	75		85	81	77	69
40	100		88	85	82	76		85	81	77	72
60	30		87	82	77	69		83	77	70	65
60	40		88	84	79	72		86	80	74	67
60	60		88	84	81	75		86	82	76	70
60	80		89	85	82	76		86	82	78	72
60	100		89	86	83	78		86	82	78	74
100	40		88	84	80	74		86	80	75	68
100	60		88	84	82	77		86	82	78	72
100	80		89	85	83	79		86	83	80	74
100	100		89	87	84	80		86	83	80	76

ORDERING INFORMATION

Explanation of Catalog Number. Example: VRA1G8LS232120SOGLR

VR

1

8

S

2

BLANK = Standard		BODY STYLE:			CEILING TYPE:				LOUVER		LAMP
N = NYC Code		A=Air Handling		G= Grid (lay-in T bar)					FINISH:		QUANTITY
		S=Static		F=Flanged (overlap)				L=Low
					Z spline and				Iridescence
	VR:		FIXTURE		plaster frame	NUMBER OF			Semi-specular	SINGLE
	3" Deep		WIDTH	T=Slot grid or			CELLS:		(standard)	WHITE
	Pre-				two-directional		1 row of	P=Low iridescence		REFLECTOR
	anodized				concealed T		8 cells		specular
	Aluminum
					(see options)
	Louver

for normal

VDT use

LAMP/

FIXTURE LENGTH: 32=T8

34=T12

(Nominal 48")

VOLTAGE:			OPTIONS:
120 or 277			Add appropriate
			suffix to catalog
	BALLAST	TYPE: no, ie: (GLR)
1-2	Lamp Mag. T12	LE		<10THD
		<20THD
1-2	Lamp Elec. T8	SO*		HI*
LOL Dimming T8		PS		–

*Instant Start Standard

Other dimming options, consult factory.

OPTIONS & ACCESSORIES

ACCESS PLATE: Top Wiring access plate is shipped with fixture as standard. When access plates are required in advance for wiring convenience, specify sepa- rately. Order Catalog Number: ACP CSP.

ELECTRICAL WIRING OPTIONS: Consult factory.

FUSING: Internal fast-blow fusing. SUFFIX: GLR. Internal slow-blow fusing. SUFFIX: GMF.

RADIO INTERFERENCE FILTER: 120 or 277 volt, 50 or 60 Hz. One per fixture

standard. SUFFIX: RF.

CONTINUOUS ROW INSTALLATION: For F type fixtures, half-width flanges are

required between fixtures. Order Catalog Number: 1FCTRIM (each joint).

SPLAY TRIM: For T ceiling type only. SUFFIX: CTZ14 S2 SPLAY TRIM.

AIR CLOSURE STRIP: SUFFIX ACS4 (factory installed).

DRYWALL KIT: Order Catalog Number: FK91X4. Request Folio OA30-10.

CHICAGO PLENUM: SUFFIX: CP.

SPECIFICATIONS

PERFORMANCE: In an installation of 2 lamp 32W luminaires in a room cavity ratio of 1, reflectance 80% ceiling, 50% wall, 20% floor, the C.U. shall not be less than .72. To prevent glare the VCP shall be not less than 86 either lengthwise or crosswise (at 100fc level) and the average brightness at 65° shall not exceed 1984 candelas per square meter. To control veiling reflections, luminaire output in the 30°-90° zone shall be not less than 67.4%.

SPECIFICATIONS (continued)

AIR HANDLING: (VRA only) side air passages for air supply or air return. Optional side closure strips. Air return is also provided through the lamp com- partment through fixture body ends.

MATERIALS: Chassis parts are die-formed embossed cold rolled steel. Housing is embossed for rigidity with all edges turned-in for safe handling. LOUVER: Pre-anodized aluminum (Coilzak@ or equal).

FINISH: Louver—low iridescence semi-specular anodized vertical grain alu- minum reflector sheet is standard. Cavity—white baked polyester minimum reflectance 86%. Phosphate undercoating. Chassis exterior—black baked polyester enamel.

ELECTRICAL: Thermally protected class “P” ballast C.B.M. approved, non PCB. If K.O. is within 3" of ballast, use wire suitable for at least 90°.

LABELS: I.B.E.W./UL and C-UL.

Job Information	Type:
Lightolier a Genlyte Thomas Company	www.lightolier.com

Technical Information: (978) 657-7600 • Fax (978) 658-0595

631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710 We reserve the right to change details of design, materials and finish.

© 2002 Genlyte Thomas Group LLC (Lightolier Division) A0902