Dolby Surround modes

Dolby Surround	Dolby Surround

Press the Dolby Surround button.

PRO-Logic is selected, and the playback sound has the Dolby Surround effect.

To cancel Dolby Surround mode

Press the Dolby Surround button repeatedly until OFF is displayed.

		Open/Close	Mute
1	2	3
		DSP/EQ	Dolby Surround
4	5	6
		S.Bass	Power
7	8	9
Disc Skip	10/0	Clear Program	Repeat
Disc Skip		Clear Program	Repeat

When playing DVD, if an Audio is Dolby Digital, it can not be operated.

When being connected to headphones and microphone, this function cannot be operated.

Additional Dolby Surround modes

In addition to the PRO-Logic mode, this unit is also equipped with the 3 STEREO modes.

PRO-Logic :Use this mode when rear speakers are connected. The center channel signals are output through the left and right speakers.

3 STEREO : Use this mode when no rear speakers are connected. This mode reproduces rear sounds through the front speakers.

PRO-Logic 3 STEREO OFF

Depending on the sound source or listening conditions, a surround effect may not be obtained even when the Dolby Surround is on. The full Dolby Surround effect cannot be obtained when using soft-

ware without			DOLBY SURROUND	mark. In this case, use the DSP
system instead.			P R O L O G I C

On/Standby

		Open/Close	Mute
1	2	3
		DSP/EQ	Dolby Surround
4	5	6
		S.Bass	Power
7	8	9
Disc Skip	10/0	Clear Program	Repeat

DVD/CD

DECK

Deck 1/2

Band

Volume

Tuning

Mode

Volume

–

Timer On/Off

Zoom

Adjusting Speaker Level Balance

The unit is equipped with a built-in test signal generator called a noise sequencer which outputs a noise signal that ‘travels’ from channel to chanel. This enables the simple adjustment of sound levels, to achieve, at the listening position, the same apparent loudness from each channel. Use the remote control.

1	Press the Dolby Surround button.
	Result: “			PRO-LOGIC” appears on the displayed.
2	Press the Test Tone button.
	A noise signal is sent to each channel in turn in the following
	sequence.
				L	CNTR	R	REAR
				L	CNTR	R	REAR
		(L : Left Speaker, CNTR : Center Speaker,
			R : Right Speaker, REAR : Rear Speaker)
3	Press the Test Tone button again to stop the noise signal.
4	To change the sound levels or delay time after adjusting the balance
	with the noise sequencer.
	Press the Sound Edit button.
	While L, R, CNTR, REAR is displayed, press the UP/DOWN
	( /	) button.
	Press the Speaker Mode button.
	While CNTR, REAR, DELAY TIME is displayed, press the
	UP/DOWN ( /				) button.

–CNTR : Large/Small/None

–REAR : USE/None

–DELAY TIME : 15/20/25/30 MS

When the Dolby surround system is on, this function can be operated.

1	2	3	Open/Close		Mute
1	2	3
			DSP/EQ	Dolby Surround
4	5	6
			S.Bass		Power Sound
7	8	9	1
Disc Skip	10/0	Clear Program			Repeat
Disc Skip		Clear Program			Repeat

DVD/CD

DECK

Deck 1/2Band

Volume

Tuning

Mode

Volume

–

Timer On/Off	4		Zoom
Sleep	Speaker Mode	Angle	Audio
Test Tone	Sound Edit	4Step	Go To
Display
	Title		Menu
Set up2,3		Enter	4
AUX	Return		Sub Title

Dolby Surround