Safety Precautions
Caution
¡ôWhen comparing the appliance with other refrigerators, please refer to the model and number;
¡ôBefore the appliance is connected to the power, verify if voltage rating of the refrigerator is same to the power voltage. The voltage can be variable from 187V to 240V; if the power voltage can not meet the requirements, an automatic transformer with a minimum output of 500W shall be used.
¡ôIf the appliance is disconnected from the power, you should wait for at least five minutes before reconnection; otherwise there may be a hazard to the compressor.
¡ôDo not store food close to the temperature sensor; otherwise it may display wrong temperatures.
¡ôDo not open and close the door too frequently or for a long time during hot weather; otherwise it may affect the efficiency of the entire unit and burden the appliance with excessive load.
¡ôDo not leave the refrigerator upside down or horizontal or keep inclined over 45 degree to the ground if necessary;
¡ôDo not pull or push the appliance by holding the door handles or exert too much upward/ downward forces on the door handle;
¡ôIf a lot of hot foods are stored at the same time or the door is opened frequently or kept open for a long period of time, the internal temperature will rise and the temperature display may flash. It will be recovered normal after a period of stable operation;
¡ôThe refrigerator must be located with an easy access to the power supply.
Alert | The cooling effects originates from refrigerant that is filled through | |
special process. Please ensure the pipes in the rear are intact. | ||
|
This appliance adopts R600a refrigerant which is combustible.
During transportation and installation, please handle the appliance carefully to protect the cooling system from damage.
The refrigerant leaked from the pipe may catch fire or hurt your eyes. If refrigerant leakage occurs, please keep away the fire or potential fire source, and keep the room aired for several minutes.
-To avoid the combustible gas composed of the refrigerant leaked from the cooling circuit and the air, please select the room size to accommodate t he appliance according to the refrigerant quantity. The room size shall be calculated as per the criterion of 8g R600a per square metres.
For details of the refrigerant quantity, please refer to the manual.
-Do not start the appliance that has any damage. If any problems, please contact the dealer or service centre.
Preparing the appliance for use
1.Remove all the packing materials of the components, and do remove the foam pad under the refrigerator during the operation;
2.Clean the interior and exterior of the refrigerator with wet warm cloth (add little neutral detergent in the warm water).
3.The power plug can be connected around one hour after the refrigerator is positioned stable, please make the appropriate operations with careful reference to the page of control panel introduction.
Changing the direction of the door opening(RL34EG*)
COVER TOP FRONT | COVER TOP UPP |
| ||
SCREW B |
|
|
| |
CAP HOLE TOP | CAP SPACER DOOR |
| ||
|
| |||
COVER HINGE UPP L |
|
|
| |
|
| HINGE UPP R |
| |
|
|
| ||
CAP HINGE HOLE | COVER HINGE UPP R |
| ||
SCREW A | CAP SCREW HANDLE |
| ||
|
| |||
SCREW F |
| SCREW C | CAP HOLE DOOR | |
CAP SCREW CABI |
| |||
|
|
| ||
CAP HINGE HOLE |
|
|
| |
SCREW A | MID HINGE |
| STOPPER DOOR | |
| SCREW E | CAP HANDLE | SCREW G | |
|
|
| ||
REINF |
|
|
| |
SCREW D |
|
| CAP HOLE DOOR | |
FOOT | HINGE LOW |
| ||
SCREW C |
| |||
FIXER HINGE LOW | SCREW D |
|
| |
|
|
| ||
STOPPER HINGE LOW |
|
|
| |
| FOOT |
|
| |
SHAFT HINGE CAP SCREW HANDLE |
| |||
Advance Type: |
|
|
| |
1. Take down the SCREW B which is fixing the COVER TOP |
| |||
FRONT and then COVER TOP FRONT. Pull out the wire inserts. |
| |||
Take down COVERHINGE UPP R | SCREW A HINGE UPP R |
| ||
COVER DOOR UPP and fridge door.Take down and fix | STOPPER DOOR | |||
to the opposite side of HINGE UPP.Take down CAP HOLE TOP at | ||||
| ||||
COVER TOP FRONT and install it on the right of COVER TOP FRONT. | SCREW G | |||
|
|
| ||
2.Take down SCREW A, SCREW E and MID HINGE of the fixing hinge and then freezer door. Take down CAP HINGE HOLE, CAP SCREW CABI and SCREW F at left and install them at right.
3.Gently incline the appliance in less than 45 degree, remove the right FOOT and unfasten SCREW D. Take down right HINGE LOW. Then take down FIX HINGE LOW,SHIFT HINGE and STOPPER HINGE LOW.Reverse STOPPER HINGE LOW and fix it to the left of HINGE LOW with FIXER HINGE LOW andSHIFT HINGE.
4.Take down the left FOOT and unfasten SCREW D. Take down and fix REINF to the right. Then fix FOOT.
5. Take off the SCREW G and STOPPERDOOR in the freezer door and install them at the left
of the door.Take off CAP HOLEDOOR, CAP SCREW HANDLE, SCREW C, ASSY HANDLE BAR, and CAP SPACER DOOR, and install them at the right of the door.
Install CAP HOLEDOOR on the left of the door.
6.Fix MID HINGE with SCREW A and SCREW E, and install the freezer door Fix
Fix HINGE UPP with SCREW A.
7.Fix the wire inserts properly.Install COVER HINGE UPP L and cover it with COVER DOOR UPP.
8.Install COVER TOP FRONT and finally fasten SCREW B.
4 | 13 |