Adjustment, Preparation | Furuno 1932 MARK-2 instruction

3. ADJUSTMENT

This section covers adjustment of the radar after installation. You will need to

•adjust tune/video amplifier level

•enter antenna height

•align heading

•adjust sweep timing

•adjust main bang suppression

•select STC curve

•set a dead sector, and

•confirm magnetron heater voltage.

These adjustments are done through the in- stallation setup menu.

3.1 Preparation

Most adjustments and initial settings may be completed on the Installation Setup menu, and you can display this menu as follows:

1.Turn off the radar. While pressing and holding down the [GAIN] control (at least three seconds), press the [POWER] key.

2.Press the [MENU] key, select “OTHERS” by using the omnipad, and press [ACQ/ ENTER] key.

3.Select “24. Installation Setup”.

4.Press the [ACQ/ENTER] key to open the Installation Setup menu.

[ Installation Setup ]

		Select item by omnipad
		and press ENTER key.
				GPS	LC
	. Nav Talker		All
	. Nav Talker		All
2	. Depth Unit		m	fa	ft
				ß F
3	. Temp Unit		ß C	ß F
4	. Hdg Sensor		Magnet	Gyro
5	. Key Beep		Off	On
				Stop
6	. Ant on Tx		Rotate	Stop
7	. Dead Sector	180ß ~180ß
8	. Tuning/Video Auto Adjustment
9	. Heading Alignment

10.Sweep Timing Adjustment

11.MBS Adjustment

12.	Ant Height	Low	Mid	High
13.	STC Curve	Sharp	Std	Gntl
14.	Ope Mode	Master	Slave
15.	Hours in Use	000001.5H
16.	Tx Hours	000000.0H

Figure 3-1 Installation Setup menu

3.2 Adjusting Tuning/Video

Do the following to automatically adjust tun- ing and video amplifier level input.

1. Press the [STBY/TX] key to transmit.

WARNING

Before transmitting the radar make sure no one is near the scanner unit, to pre- vent the potential risk of being struck by the rotating scanner and exposure to RF radiation hazard.

2.On the Installation Setup menu, select “8. Tune/Video Adjustment” and press the [ACQ/ENTER] key.

3.The unit automatically adjusts tuning and video, displaying the following message.

[ Tune/Video Auto Adjustment ]

Now under correction.

Return to installation setup menu after the correction.

Figure 3-2 Tune/video auto

adjustment message

4.When adjustment is completed, the mes- sage disappears.

3.3 Entering Antenna Height

The STC curve changes with respect to an- tenna height above the waterline. Enter an- tenna height above the waterline to optimize the STC curve.

1.Select “12. Ant Height” from the Installa- tion Setup menu and press the [ACQ/EN- TER] key.

2.Operate the omnipad to select antenna height above the waterline; Low (3 m or less), Mid (3 to 6 m) or High (6 to 10 m).

3.Press the [ACQ/ENTER] key.

3-1

1932 MARK-2 specifications

The Furuno 1932 MARK-2 is a state-of-the-art radar system designed for maritime applications, providing exceptional performance and reliability. This advanced radar unit is renowned for its impressive range, superior target detection capabilities, and user-friendly interface, making it an essential tool for vessels of all sizes.

One of the standout features of the Furuno 1932 MARK-2 is its high-resolution display. The 10.4-inch color LCD screen offers crystal-clear visuals, enabling mariners to easily interpret radar data. With the capability to display 16 different colors, users can customize their views for enhanced clarity, allowing for better discrimination between targets and clutter. Additionally, the unit incorporates adjustable gain and clutter control, giving operators the ability to fine-tune the radar image to suit varying conditions, whether in busy harbors or open waters.

The 1932 MARK-2 utilizes a powerful 2.2 kW magnetron, allowing for excellent range performance. It can effectively detect targets up to 36 nautical miles away, providing mariners with ample warning of potential hazards. This long-range capability is complemented by advanced target tracking technologies, including ARPA (Automatic Radar Plotting Aid). This system enables users to monitor and track multiple vessels simultaneously, providing essential information such as course, speed, and distance for better situational awareness.

In terms of technology, the Furuno 1932 MARK-2 includes a Fast Target Update feature. This allows for rapid refresh rates, ensuring that moving targets are accurately displayed, even in heavy traffic areas. The unit also employs advanced digital signal processing to filter out noise and improve target detection, enhancing overall operational efficiency.

Another key characteristic of the 1932 MARK-2 is its robust build quality. Designed to withstand the marine environment, the unit features a waterproof casing with an IP55 rating, ensuring durability against splashes and humidity. Furthermore, its compact design offers versatile mounting options, making it adaptable for various vessel configurations.

Overall, the Furuno 1932 MARK-2 radar system stands out for its blend of advanced technology, user-centric features, and rugged reliability. Its ability to provide clear and accurate radar imagery makes it an invaluable asset for navigators, enhancing safety and efficiency on the water. As an investment in maritime technology, it offers significant advantages to enhance both recreational and commercial navigation.