MTX Audio XT110P Specifications, Precautions, System Protection Features, Included Accessories

Page 2

Thank you for purchasing the X ThunderLink Amplified Subwoofer System. To be sure you get the most from your new system, please read this manual carefully and follow the precautions and instructions.

SPECIFICATIONS

Power Output: 100 Watts RMS @ 4 Ohms

THD+N (Distortion) (1 Watt): < 0.25%

Signal-to-Noise Ratio (1 Watt): > -90dB

Dimensions: 15 5⁄8” x 12 1⁄8” x 8 5⁄8”

PRECAUTIONS

To reduce the risk of accident and fire, please observe the following warnings:

•Use with 12VDC only

•Use 10 gauge or larger power and ground wire

•Connect the power wire directly to the positive terminal of the vehicle’s 12V battery. Be sure to use an in-line fuse within 18” of the battery on the power wire connected to the positive terminal.

•In the event of a blown fuse, replace the fuse with a 20A fuse only. Any other fuse value could result in damage to your product.

•Securely fasten ground to bare metal close to vehicle frame (not factory bolts).

WARNINGS

•The X ThunderLink will not operate when an external protective function is enabled. To restore normal operation, eliminate the protective function before disconnecting and reconnecting power to the

X ThunderLink.

•Normal operation of the X ThunderLink will cause the surface to heat up. Do not install this product near heat sensitive materials to avoid fire and other damage.

•Securely mount the X ThunderLink to your vehicle in a safe location to prevent damage to the product and bodily injury in the event of an accident. Use the mounting brackets provided.

•Do not install this product where it will be exposed to moisture, extreme heat, or will interfere with normal driving.

SYSTEM PROTECTION FEATURES

•The X ThunderLink is designed to operate from 8VDC to 17VDC. Voltage outside this range will cause the unit to not operate properly.

•The X ThunderLink is equipped with a thermal protection circuit to prevent damage. A Red LED will illuminate if the amp goes into thermal protection mode.

INCLUDED ACCESSORIES

20A Fuse (1)

Wire Harness (2)

Remote Control (1)

MOUNTING INSTRUCTIONS

VERTICAL MOUNTING:

1.Choose a suitable location (preferably the trunk) to install the X ThunderLink that observes all warnings and installation instructions previously stated.

2.Snap the two vertical mounting brackets into place on the bottom of the X ThunderLink using the molded indentations as a guide. Be sure the molded nut on the bracket is opposite the control panel to provide easy access to the control panel for fine tuning (See Figure 1).

3.Insert one of the provided bolts through each of these bottom two holes in the X ThunderLink and securely fasten the bracket using a screwdriver. Note: You will only use two bolts when mounting the X ThunderLink vertically.

4.Securely mount the X ThunderLink to the vehicle through the screw holes in the mounting brackets with the screws provided.

FIGURE 1

HORIZONTAL MOUNTING:

1.Choose a suitable location (preferably the trunk) to install the X ThunderLink that observes all warnings and installation instructions previously stated.

2.Snap the four horizontal mounting brackets into place, using the molded indentations as a guide. Be sure the molded nut on the bracket is opposite the control panel to provide easy access to the control panel for fine tuning (See Figure 2).

3.Insert one of the provided bolts through each of the holes in the X ThunderLink and securely fasten the bracket using a screwdriver.

4.Securely mount the X ThunderLink to the vehicle through the screw holes in the mounting brackets with the screws provided.

FIGURE 2

 

Vertical Mounting

Horizontal Mounting

M5x190 Bolt (4)

Self Tapping

 

Bracket (2)

Bracket (4)

 

Screw (4)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Page System Protection Features SpecificationsPrecautions Included AccessoriesNo Power Amplifier Controls and Power Wire ConnectionTroubleshooting Problem Possible Cause Solution Power but no SoundAdvertencias EspecificacionesPrecauciones Características DE Protección DEL SistemaDetección Y Reparación DE Averías Problema Posible Causa SoluciónControles DEL Panel Delantero No HAY AlimentaciónAvertissements Accessoires InclusCaracteristiques Techniques Caracteristiques DE Protection DU SystemeAucune Alimentation Commandes DU Panneau AvantResolution DES Problemes Possible Cause Solution SONPage O U D S P O N S O R O F

XT110P specifications

MTX Audio has long been recognized as a leader in the automotive audio industry, providing high-quality products that enhance the listening experience. One such standout product is the MTX Audio XT110P, a powerful subwoofer that merges innovative technology with exceptional performance to deliver deep, resonant bass for music enthusiasts.

The MTX Audio XT110P boasts a robust design, featuring a 10-inch subwoofer that is engineered to provide powerful low-frequency response. With its smart engineering, the XT110P is capable of producing an impressive peak power handling of up to 600 watts, and an RMS power of 300 watts. This power allows the subwoofer to create deep, punchy bass that can be felt as well as heard, making it an ideal choice for those seeking to elevate their car audio system to new heights.

One of the key features of the XT110P is its vented polypropylene cone, which contributes to the subwoofer’s durability and sound quality. This material allows for efficient sound reproduction while also providing the necessary strength to withstand the rigors of daily use. Additionally, the butyl rubber surround enhances the subwoofer's ability to produce clean and distortion-free bass, ensuring a rich audio experience.

Further enhancing its performance, the MTX Audio XT110P incorporates a high-temperature voice coil that promotes efficient energy transfer and prevents overheating during extended listening sessions. This technology not only maximizes the subwoofer's output but also extends its longevity, ensuring that users can enjoy robust bass without worrying about wear and tear.

Installation versatility is another hallmark of the XT110P. The subwoofer comes equipped with a durable enclosure that is designed to fit into a variety of vehicle types and spaces, providing users with flexibility in installation options. This plug-and-play design makes it easier than ever for car audio enthusiasts to upgrade their system without extensive modifications.

The MTX Audio XT110P is built with the audiophile in mind, balancing power, clarity, and durability. Its combination of high-quality materials, innovative technology, and thoughtful design ensure that it not only meets but exceeds user expectations. Whether you're a casual listener or a dedicated audiophile, the XT110P offers an unparalleled audio experience that brings your music to life. With its blend of performance and reliability, the XT110P continues to be a preferred choice for those looking to deepen their connection to the music they love.
Top Page Image Contents