Desa BLP100, REM100LP owner manual Service Procedures, Motor

Page 7

SERVICE PROCEDURES

7

SERVICE PROCEDURES

WARNING: Never service heater while it is plugged in, connected to propane supply, operating, or hot. Severe burns and electrical shock can occur.

Transformer

GroundGreen Lead

Screw

MOTOR

1.

With heater on its side, remove base tray.

2.

Access ground screw through underside of heater base. Re-

 

move ground screw. Disconnect the green motor wire and the

Motor

Green

Lead

Power Cord Green Lead

 

green power cord wire from underside of shell (see Figure 5).

3.

Remove black and white motor wires from terminal board (see

 

Figure 5).

4.

Carefully push motor wires through hole in bottom of shell.

5.

Remove screws holding motor mount to shell. Use nut-driver

 

(see Figure 6).

6.

Carefully pull motor and fan out of shell. IMPORTANT: Be

 

careful not to damage fan. Do not set motor and fan down with

 

the weight resting on fan. This could damage fan pitch.

7.

Use hex wrench to loosen setscrew which holds fan to motor

 

shaft.

8.

Remove fan. Be careful not to damage the fan blade pitch.

9.

Use nut driver to remove two nuts that attach motor to mo-

 

tor mount.

10.

Discard old motor.

11.

Attach motor to motor mount with two nuts. Tighten nuts firmly.

12.

Replace fan on motor shaft. Make sure set screw contacts flat

 

surface on motor shaft.

13.

Tighten set screw firmly (40-50 inch-pounds).

14.

Carefully route motor wires through hole in shell (see Figure 7).

 

Place motor, motor mount, and fan guard into rear of heater shell.

15.

Insert screws through heater shell and into motor mount.

 

Tighten screws firmly.

16.

Turn heater on its side to access opening in bottom of base.

 

Connect green wires from motor, transformer, and power cord

 

to heater shell using ground nut (see Figure 5).

17.

Attach black and white wires to terminal board (see Wiring

 

Diagram, page 9, for correct locations) .

18.

Replace base tray.

Terminal

Board

Figure 5 - Location of Ground Screw

Motor

Mount

Screw

 

Fan

 

Guard

 

Motor

Hole in Shell

Mount

for Wires

 

Figure 6 - Removing Motor, Motor Mount, and Fan Guard from Heater

Hole in

Shell for

Wires

Figure 7 - Replacing Motor, Motor Mount, and Fan Guard into

Heater

For more information, visit www.desatech.com

102370-01K

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Propane Construction Forced AIR Heater Table of ContentsSafety Information Product Identification UnpackingTheory of Operation Propane Supply InstallationVentilation To Stop Heater MaintenanceOperationstorage To Start HeaterObserved Fault Possible Cause Remedy TroubleshootingMotor Service ProceduresSpark Transformer FANIgnitor Wiring Diagram SpecificationsAccessories Models Illustrated Parts BreakdownREM100LP KEY Part Number Description QTY Parts ListParts Under Warranty Technical Service Replacement PartsParts not Under Warranty Owners Registration Form Postage Required GAS Chimeneas PROPANE/LP Forced AIR Heaters PROPANE/LP Convection HeatersWarranty Service Warranty and Repair ServiceKeep this Warranty Limited Warranty

BLP100, REM100LP specifications

Desa BLP100 and REM100LP are two remarkable offerings in the world of advanced sustainable energy solutions, each designed to meet specific needs while promoting environmental responsibility.

The Desa BLP100 is a state-of-the-art battery energy storage system that highlights efficiency and reliability. One of its main features is the integration of lithium-ion technology, accommodating a robust energy capacity. This allows the BLP100 to serve both residential and commercial applications, managing energy storage during low-demand periods and delivering power when needed most. The system is designed for easy scalability, enabling users to expand their storage capabilities as their energy needs grow.

The BLP100 is equipped with intelligent management software that optimizes charging and discharging cycles, ensuring maximum battery life while enhancing overall performance. This technology also provides real-time monitoring and analytics, allowing users to have complete insight into their energy consumption patterns. Safety is paramount in the BLP100; it comes with multiple layers of protection against overcharging, overheating, and short circuits.

On the other hand, the REM100LP is an innovative solar energy solution tailored for users looking to harness renewable energy effectively. Its primary feature is the high-efficiency photovoltaic solar panels, which convert sunlight into electrical energy with low environmental impact. The REM100LP is designed with a compact form factor, making it suitable for a variety of settings, from urban rooftops to remote locations.

Its lightweight design, coupled with durable materials, ensures ease of installation and long-lasting performance under various weather conditions. Additionally, the REM100LP incorporates advanced inverter technology, which optimizes the conversion of direct current (DC) to alternating current (AC), thereby providing stable electricity for various applications.

Both the Desa BLP100 and REM100LP systems are examples of how modern technology can address energy challenges while promoting sustainability. Their commitment to integrating cutting-edge technologies exemplifies the future of energy management, where efficiency, safety, and eco-friendliness are paramount. By adopting these systems, users not only benefit from lower energy costs but also contribute favorably to environmental preservation, making a significant impact in the pursuit of global sustainability goals.
Top Page Image Contents