Draper SLX13, SLX12, SLX16, SLX14 dimensions Please Check All Appropriate Selections, Select Model

Scissor Lift–SLX Series					Video Projector Lift			by
					Motorized Ceiling-Recessed
DIMENSIONS & DATA	MODEL SLX11 MODEL SLX12 MODEL SLX13				MODEL SLX14		MODEL SLX15	MODEL SLX16	MODEL SLX17
Height of lift in closed position*	13¾"	15¾"	15¾"		171/8"		171/8"	191/8"	191/8"
Overall lift dimensions (WXL**)	27" x 29½"	27" x 29½"	27" x 29½"		27" x 29½"		27" x 29½"	27" x 29½"	27" x 29½"
Max. down travel (Service Position)	11'	12'	13'		14'		15'	16'	17'
Approx. travel time to serv. position	99 sec.	108 sec.	117 sec.		125 sec.		134 sec.	143 sec.	152 sec.
Capacity (lbs.)	350	350	350		350		350	350	350
Net weight (lbs.)	160	165	170		175		180	185	190
Shipping weight (lbs.)	186	191	196		201		206	211	216
Amperes***	2.6	2.6	2.6		2.6		2.6	2.6	2.6
Show Position — Set at factory. Can specify at time of order
Max. projector height — If recessed, limited only by amount of available space above the ceiling
Min. clear space above fi nished ceiling — Will vary according to projector height, optional mounting bracket, optional ceiling closure, optional plenum housing
		Size E	Size J		Size G	Size U
Max. Projector Size W x L		25½" x 35½"	25½" x 39½"	31½" x 44½"		27½" x 30½"
Ceiling Opening W x L		29½" x 40"	29½" x 44"	357/8" x 49"		367/8" x 367/8" (Trim edge–to–edge)
Ceiling Closure Panel W x L		30" x 405/8"	30" x 44½"	363/8" x 49½"		373/8" x 373/8" (Trim edge–to–edge)

Optional ceiling mounting bracket — SMS Low Profi le for projector lifts.

Optional plenum housing — Height, width and length will vary according to choice of projector

*Only height of Scissor Lift in closed position. Overall height of projector, plus optional mounting bracket, plus optional ceiling closure, plus optional plenum housing adds to overall height of equipment installed above ceiling. SMS Low Profi le Bracket adds 47/8" to height, including universal projector bracket.

**Length includes the ½" cable carrier of the Cable Management System.

***Does not include any load placed on Scissor Lift’s prewired power cable.

Please Check All Appropriate Selections

Select Model:

Model SLX11	Model SLX14	Model SLX17
Model SLX12	Model SLX15
Model SLX13	Model SLX16

Select Controls: This unit comes standard with one 12v Toggle Switch and 12v Momentary Key Control. For other switching options, please select from below:

Optional Video Interface Control(VIC12) for projection screen operation Optional Key Operated Power Supply Key Switch (On-off)

Optional LVC-III — 24v (low voltage)*

*This is required for any of the following options:

Wireless Remote Control (radio frequency transmitter & receiver) Wireless Remote Control (infrared transmitter & receiver)

Select Optional Accessories:

Optional factory installed cables for RGBHV, Video, and RS232 Specify connector types:

Optional ceiling closure

E J

G U Optional ceiling fi nish kit

Optional 2' x 2' ceiling access door to allow access above fi nished ceilings White painted fi nish

Accepts ceiling tile

(Please Note: option ceiling access door is highly recommended.) Optional plenum housing

Optional SMS Low Profi le Projector Bracket (Max. load 26 lbs.)

If you are ordering an SMS Low Profile Projector Bracket with this unit, please specify projector manufacturer and model number:

(If not available at time of order, it may be provided later)

Specifications—Scissor Lift U.S. Patent D395,909

video projector lifts, Model (SLX11-17), for projectors weighing up to 350#. Dove grey baked powdercoat fi nish. Projector bolts onto operating pan, or mount to pan with optional SMS Low Profi le Lift Bracket. Electrically operated

110-120V AC, 60 Hz. UL recognized gearmotor, with metal chain drive system, to be lifetime lubricated. Draws 2.6 amps. Projector to be suspended from 31/4" x 24" x 26" x 11 ga. steel pan supported by steel scissor arms and operated by two, 3/16" aircraft cables with 4200 foot/pounds tensile strength per cable. Scissor Lift equipped with 3 sets of stabilizing scissors, positioned on the left, right, and rear sides. Also equipped with fail-safe inertial safety belt system and Cable Management System with projector power cord. Factory set limit switches to automatically stop travel at store, show, and service positions. Single Station Control, standard, consists of one 12V toggle switch to lower lift from “stored” to “show ” positions, and one 12V momentary key switch to lower lift from “show” to “service” position. Optional LVC-III for operation from “stored” to “show” positions only; required for use with Key Operated Switch.

Optional plenum housing consists of suitable painted steel panels for use in return air plenum situations. Optional ceiling closure panel, fi nished in white baked textured powdercoat, shall descend smoothly with projector. Choose a model based on number of feet needed (11'-17') to put projector within easy reach for servicing.

Please Note: The Scissor Lift should be specified in conjunction with a DRAPER motorized screen.

SMS Low Profile Fixed Mount: Ceiling mount shall consist of a steel ball joint and Universal Projector Bracket. Mount shall be 2" long, and shall securely attach to lift with steel mounting plate (provided). Installer shall provide mounting hardware appropriate to ceiling conditions. Steel ball joint attaches to Universal Projector Bracket with twist-lock engagement. Min. overall height of assembled unit shall be 47/8". Mount shall provide up to 30° roll or pitch adjustment and 360° yaw adjustment at ball joint. Two setscrews lock ball joint in position. Max. load 26 lbs. Ceiling Access Door: Provides access to projector and lift when unit is installed above hard ceiling. Finished by ceiling contractor to match ceiling.

Copyright © 2007 Draper Inc. Form ScissorLift-SLX_Sub07-R Printed in U.S.A.

PROJECT:

ARCHITECT:

CONTRACTOR:

SUPPLIER:

DATE:REVISED: