Oreck U2007RH warranty Parts List, Assembly, Operating Instructions

E N G L I S H

Parts List

To assist you in identifying components of your vacuum, the parts have been numbered as follows:

1	Handle section, upper
2	Tube, lower	10
				11
3	Power head	9
4	Outer bag			1
			12
5	Paper filter dust bag
				17
6	Power cord
7	Retaining spring	5		16
8	Bag tension bar
			13
		4
9	Zip fastener
10	On/off switch
11	Cord hook		2	6
12	Plastic loop/cable clamp
13	Connector assembly
14	Fan housing	8 7	14	15
15	Cord assembly
16	Handle Brace	3
17	Cord Strain Relief

Assembly

fig. 1 Before assembling appliance, remove two screws from the connector assembly. Remove cardboard insert by pulling upward.

fig. 2 Slide upper handle section over matching section of the connector assembly. Place brace against handle and connector assembly aligning screw holes. Insert short screw into top hole and long screw into the bottom hole then tighten firmly until handle is no longer loose.

fig. 3 Attach cord to cord clip by pressing above and below clip ensuring the cord is fully rested in clip.

Operating Instructions

Make sure the disposable paper filter dust bag is in place. DO NOT operate the cleaner without a paper filter dust bag. Plug the power cord into an electrical outlet. Press the On(l) - OFF(O) switch on handle assembly when ready to operate. Choose from the low and high speed settings by pressing the ON/LOW

(l)ON/HIGH (ll) - OFF (O) switch on handle assembly when ready to operate.

General Information

The performance of your new cleaner greatly depends upon care and maintenance. The instructions in this manual will guide you in performing basic care and maintenance. To obtain the most satisfying years of service read the instructions and keep them handy for future reference.

Operating Recommendations

This new ORECK XL High-Speed Upright is one of the finest, fastest, and strongest units in its class. You’ll love the way it cleans, gets under things, and it’s SO lightweight and easy to use.

The following are a few simple suggestions regarding its operation:

1.When inserting a new disposable paper filter dust bag— FIRST PUFF OUT and OPEN THE BAG.

2.When the disposable filter dust bag is full, REPLACE IT.

3.If at any time the machine does not pick up properly or makes an unusual noise, STOP OPERATION and service.

4.Although your upright will pick up pins, paper clips, and other small objects, it is recommended that these be removed from the floor before you vacuum. Failure to do so may result in permanent damage to the motor suction fan and its housing.

5.WARNING: Do not use your vacuum cleaner on damp or wet surfaces. This will cause damage to the vacuum cleaner and is dangerous to the user. Damage caused by use on wet or damp surfaces is not covered under warranty.

6.REPLACE THE BELT EVERY 6 MONTHS.

7.Change the disposable filter dust bag at least once a month—even if it is not full! The collected dust in the dust bag can cause odor, attract moisture, act as a breeding area and can affect the efficiency of the cleaner.

8.DO NOT run the vacuum cleaner over cord. The revolving brush could damage the cord.

9.Use caution when vacuuming over area rug edges and fringe.

Disposable Paper Filter Dust Bags

Disposable paper filter dust bags play a very important role in the efficiency of your ORECK vacuum cleaner. The purpose of the paper bag is to trap dirt, but at the same time it must be porous enough to allow air to pass through. If the paper bag becomes clogged, no air can pass through the cleaner and cleaning cannot take place, regardless of the cleaner’s power. Increase the CLEANING POWER of your cleaner by changing the bag often.

To keep your cleaner operating at maximum efficiency, change the dust bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG.

Be sure the disposable paper filter dust bag is installed properly.

All paper dust bags are not the same. Your ORECK disposable dust bags have been designed to be used with the ORECK cleaner. Using bags other than genuine ORECK disposable bags will affect the cleaning ability of your cleaner and could cause damage to it.

The Belt

The belt on your vacuum cleaner controls the speed of the revolving brush and is very important for the effective operation of the cleaner. If the belt becomes stretched or cut, it will cause the revolving brush to stop completely or slow down. See instructions in the manual for replacing belt.

An extra belt is stored in the baseplate of your cleaner. When buying replacement belts, use ONLY ORECK genuine belts. Belts other than Oreck belts will not operate the revolving brush correctly and may create undue stress which will cause damage to the motor and brush bearings. Using belts other than ORECK belts will void the warranty.

5