Heath Zenith SL-5412 manual Installation, Wall Mount Eave Mount, Black to White to

Page 2

INSTALLATION

Twist the junction box wires and fixture wires together as shown. Secure with wire connectors.

For easy installation, select an existing light with a wall switch for replacement.

Wall Mount

Eave Mount

For under eave installation, the sensor head must be rotated as shown in the next two steps for proper operation and to avoid the risk of electrical shock.

Mounting

Strap

Black to

Black

White to

White

Rubber

Plug

Mounting

Bolt

Gasket

For eave mount only:

Swing the sensor head towards the clamp screw

joint.

Controls

Clamp Screw

Then rotate the sensor head clockwise 180° so the controls face down.

Controls

Controls

If the sensor pops out of the ball joint, loosen the clamp screw and push the sensor back into the ball joint. Tighten the clamp screw when done.

Wire the Light Control

WARNING:Turn power off at the fuse or circuit breaker.

Remove the existing light fixture.

Install the mounting strap as shown using two screws that fit your junction box.

The plastic hanger can be used to hold the fixture while wiring. The small end of the plastic hanger can be threaded through the hole in the center of the cover plate. The small end then goes into one of the slots on the mounting strap.

Route the light control’s wires through the large gasket holes.

Junction box ground wire to green ground screw on fixture.

Mount the Light Control

Align the light control cover plate and cover plate gasket. Secure with the mounting bolt.

Align the three slots in the decorative shell with the lamp holder pins. Push the shell in and then twist clockwise to lock. Repeat for other shell.

Shell Slot

Push the Rubber Plug firmly into place.

If a wet location junction box was not used, caulk the wall plate mounting surface with silicone weather sealant.

To avoid water damage and electrical shock, keep lamp holders 30° below horizontal.

 

Keep lamps at least

 

1" (2.5 cm) from the

Lock Nut

sensor.Do not allow

 

the lamps to block

Lens

the lens.

Adjust the lamp holders by loosening the lock nuts but do not rotate the lamp holders more than 180° from the factory setting. When screwing in the floodlamps, do not overtighten.

598-1265-01

Image 2
Contents Model SL-5412 FeaturesOperation RequirementsWall Mount Eave Mount InstallationWire the Light Control Black to White toBottom of Sensor Test and AdjustmentSpecifications Maximum RangeSymptom Possible Cause Troubleshooting GuideNo Service Parts Available for this Product Características FuncionamientoModelo SL-5412 RequisitosNegro a Blanco a Blanco InstalacionMontaje en pared Montaje en alero ADVERTENCIAApague la energía en el fusible CortacircuitosParte de abajo del detector Prueba Y AjusteEspecificaciones Alcance Máximo Angulo de Cobertura MáximaNo hay piezas de servicio disponibles para este producto Guia DE Investigacion DE AveriasServicio Técnico Garantía Limitada a 10 AñosModèle SL-5412 Résumé du mode de commutationFonctionnement CaractéristiquesBlanc Noir / Noir /Blanc Montage sousMontage mural Avant-toit Le crochet en plastique peut peut servir à supporter leBas du détecteur Essais ET RéglagesFiche Technique Portée maximale Angle de Couverture maximaleAucune pièce de rechange n’est disponible pour ce produit Service TechniqueGuide DE Dépannage Symptôme Cause Possible
Related manuals
Manual 8 pages 51.63 Kb

SL-5412 specifications

The Heath Zenith SL-5412 is a remarkable piece of technology in the realm of outdoor lighting and security solutions. With its blend of aesthetic design and advanced functionality, this motion sensor light fixture has become a popular choice for homeowners seeking to enhance their exterior spaces.

One of the standout features of the SL-5412 is its dual-lens motion sensing technology, which is designed to detect movement with impressive accuracy. The dual passive infrared sensors work simultaneously to cover a vast area, significantly reducing the chances of false alarms that can occur with single-sensor systems. This technology allows the fixture to be adjustable, providing a customizable experience that can suit various outdoor settings.

The SL-5412 also boasts a powerful LED light source, which delivers bright illumination while being energy-efficient. The fixture typically generates a lumen output that provides excellent visibility for any outdoor area, enhancing safety and security around the home. Additionally, LED bulbs have a longer lifespan compared to traditional incandescent bulbs, reducing the frequency and cost of replacement.

A key characteristic of the Heath Zenith SL-5412 is its weather-resistant construction. Built to withstand diverse weather conditions, the fixture is ideal for outdoor use, ensuring durability and reliability in any climate. Its rugged design not only protects it from rain and wind but also contributes to long-term maintenance-free operation.

The adaptability of the SL-5412 is further highlighted by its adjustable settings. Users can easily modify the sensitivity of the motion sensors, the duration of light activation, and the ambient light threshold, allowing for precise control over the unit’s performance in response to surrounding conditions.

Another notable aspect of this security light is its sleek design, which blends seamlessly with most home exteriors. Available in multiple finishes, the SL-5412 enhances the aesthetic appeal of outdoor spaces while serving its primary purpose of providing safety and visibility.

In summary, the Heath Zenith SL-5412 combines modern technology with thoughtful design features to create a versatile solution for outdoor lighting and security. Its dual-lens sensing technology, energy-efficient LED output, weather-resistant durability, and customizable settings make it an exceptional choice for any homeowner looking to improve their outdoor environment. As security and efficiency continue to be a priority in home improvement, the SL-5412 stands out as a reliable and effective option.